1) front-end parts
前端部件
2) front end
前端
1.
The design of the Transmit/Receive front end of the B mode ultrasonic instruments base on FPGA;
基于FPGA的B超收发前端电路设计
2.
The vacuum fast protection system for synchrotron radiation beamline front end;
同步辐射光束线前端真空快保护系统
3.
Research on noise figure of microwave and millimeter wave reception front end with wide frequency;
微波宽频接收前端低噪声的研究
3) front-end
前端
1.
Probing of digital campus network and front-end;
数字化教学网建设与前端浅探
2.
Implementation of digital set top box receiver front-end based on DVB-T;
基于DVB-T的数字机顶盒接收前端实现
3.
The STB software structure is described with focus on the software of front-end control,program management and CA interface.
文章对机顶盒的软件结构进行了概述并重点介绍了前端控制软件、节目管理软件和有条件接收接口软件。
4) Front terminal
前端
1.
Front terminal is one of the most important components for telemedicine systems.
远程医疗系统前端是远程医疗系统的重要组成部分之一,研究高性能且低价格的医疗前端对推动远程医疗系统的广泛应用有着十分重要的意义。
5) front-ends
前端
1.
Frequency planning of radio frequency front-ends receiver;
射频前端接收机频率规划
2.
Recent progress in 10~40Gb/s OEIC receiver front-ends;
10~40Gb/s OEIC光接收机前端的最新研究进展
6) Forehand Plate
前端板
1.
Manufacture of Forehand Plate of Air-conditioner Compressor for Car by Shell Mold Method;
车用空调器压缩机前端板铸件壳型铸造工艺实践
参考词条
补充资料:将UG里的一个装配部件输出成单个部件文件
法一:
- 关闭(turn off)FileàOptions->Load Options下"Partial Loading "选项
- 打开装配部件
- 选择File->Export->Part
- 在"Part Specification"下选择"new"
- 选择"Specify Part",指定输出部件文件名称及位置
- 将"Object Selection Scope"设定为"All Objects"
- 选择"Class Selection->Select All"高亮所有对象
- 按"OK"
该种方法特点:每一个部件的特征都会汇集在新部件的MNT里。可以方便编辑。
法二:
- 闭(turn off)File->Options->Load Options下"Partial Loading "选项
- 打开装配部件
- Application->Assembly
- Assemblies->Components->Create New,给出想要输出的部件文件名及路径。
- 如下图1,在ANT上双击新产生的部件文件,使其成为工作部件。
- Assemblies->WAVE Geometry Linker,将设置改为"Body",选择所有组件的体。
- 将"Create Non-associative"开关设为"On",见下图2
- 将产生的部件设成显示部件,仅保存刚产生的新部件,不保存旧的装配部件。
图1 | 图2 |
该种方法特点:每一个部件在新部件的MNT里只会显示一个link的特征。没有相应特征可以编辑。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。