|
|
1) Dependability profile
可信剖面
2) information section
信息剖面
1.
Based on the obtained simulation result of typical numerical value and with the help of information section of apparent resistivity anomaly,the anomalies are analyzed and studied,and the anomaly features and their variation regularity are summarized,and on this basis,the anomaly features of ot.
根据所得的典型数值模拟结果，借助视电阻率异常信息剖面图，对异常进行研究，总结了异常特征及其变化规律，并以此为基础分析和认识了其他模型的异常特征。
3) drillability profile
可钻性剖面
1.
To improve the drilling penetration rate and reduce drilling cycle in Chenghai Region2 of Dagang Oilfield, approach of cluster analysis was used to process and analyze rock drillability calculated from logging data, the rock drillability profile of lateral formation in Chenghai Region 2 and low of vertical rock drillability changes in the whole region were established.
为提高大港油田埕海二区钻井速度,降低钻井周期,利用聚类分析方法对测井资料计算出来的岩石可钻性级值进行处理和分析,建立了埕海二区横向地层岩石可钻性剖面及整个区块内地层岩石可钻性纵向变化规律,找出了该区块地层岩石横向及纵向可钻性变化规律,可用于指导生产实践。
4) visual the section
剖面可视化
5) Songke'er section
松可尔剖面
1.
Because of the chaotic stratigraphic division of the Mid-Lower Jurassic dark-colored rock series in the Doima stratigraphic area, southern Qiangtang, the authors measured the Songke′er section in Sêwa during the petroleum geological survey in 2005 and systematically collected abundant ammonoid fossils with chronological significance.
针对南羌塘多玛地层分区中—下侏罗统深色岩系地层划分的混乱状况,2005年在进行羌塘盆地石油地质调查中实测了色哇地区松可尔剖面,并系统采集到大量有时代意义的菊石化石。
6) Message-Profile-Map
信息剖面图
1.
Locating Underground Abnormal Object with Message-Profile-Map;
利用信息剖面图进行地下异常体定位
补充资料：关于solidworks 中的剖面线中的剖面线
solidworks的剖面线线型定义和autocad相同,它使用了autocad的剖面线定义方法,与autocad通用.因此,可以对剖面线进行定义. 方法:修改\SolidWorks\lang\chinese-simplified\sldwks.prn 用笔记本打开该文件,添加需要的线形.如 ;; Based on AutoCAD Ver.13.0s Hatch Pattern File ;;;; solidworks 区域剖面线定义文件 :: *金属, (Iron BrickStone), ANSI Iron, Brick, Stone masonry 45, 0,0, 0,.125 *塑料, (Lead Zinc Mg), ANSI Lead, Zinc, Magnesium, Sound/Heat/Elec Insulation 45, 0,0, 0,.125 135, 0,0, 0,.125 *玻璃,AR-GLASS@1.0 45,0,0,0,0.5, 0.5,-0.5 45,0,0.1414214, 0,0.5, 0.3,-0.7 45,0.1414214,0, 0,0.5, 0.3,-0.7 *软木, Cork material@1.0 0, 0,0, 0,.125 135, .0625,-.0625, 0,.35355339, .176776696,-.176776696 135, .09375,-.0625, 0,.35355339, .176776696,-.176776696 135, .125,-.0625, 0,.35355339, .176776696,-.176776696 *无, None 删除不需要的定义类型,可以大大提高solidworks 的启动速度
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条
|