1) modification in cross section
端面修饰
2) terminal modification
末端修饰
1.
A human YAC genomic pool with more than 4 000 clones was constructed by means of "terminal modification" of YAC vector and genomic inserts, as well as optimization of rele-vant experimental pararneters.
采用“末端修饰法”修饰酵母人工染色体(YAC)载体与基因组插入片段的酶切末端,并优化各个实验参数,成功地得到了4000多个YAC片段的克隆群,转化率为400~500转化子/μgDNA。
4) surface modified
表面修饰
1.
Experimental study on fluorine-heparin surface modified intraocular lenses;
氟-肝素表面修饰人工晶状体的实验研究
2.
It was inferred that the crystallization ends when the fronts of the spherulites in the surface modified PEG particle arrive the wall.
采用乙基纤维素对聚乙二醇(PEG)粒子进行表面修饰,通过对修饰后PEG粒子和未修饰PEG粒子进行差示扫描量热(DSC)测试,研究PEG材料尺寸对非等温结晶过程的影响。
3.
The structure of surface modified FeS nanoparticle by dialkyldithiophosphate(DDP) molecules was investigated by TEM,DSC,XRD and FT-IR.
采用表面修饰的方法,以双十八烷基二硫代磷酸盐(DDP)为表面修饰剂,制备了双十八烷氧基二硫代磷酸(DDP)表面修饰的FeS纳米微粒。
5) surface-modified
表面修饰
1.
Synthesis of solvent-stabled copper nanoparticles surface-modified with platinum and their catalytic properties;
表面修饰铂的铜纳米颗粒的制备及催化性能
2.
Preparation of Valaciclovir Loaded Bovine Serum Albumin Nanoparticles Surface-modified with Glycyrrhizin and Its Characteristics of Targeting to Liver;
甘草酸表面修饰万乃洛韦白蛋白纳米粒的制备及其肝靶向性研究
3.
Synthesis of copper nanoparticles surface-modified with self-assembled monolayers
单分子层表面修饰铜纳米颗粒的制备方法
6) surface-modification
表面修饰
1.
Surface-modification and Characterization of Silica Nanoparticles;
二氧化硅纳米粒子表面修饰及其表征
2.
Study on surface-modification of CeO_2 nanoparticles by stearic acid;
硬脂酸对CeO_2纳米粒子的表面修饰研究
3.
Research progress on surface-modification of nanoparticles;
纳米微粒表面修饰的研究进展
补充资料:车端面、切槽和切断
一、车端面
常用的端面车刀(弯头刀和偏刀)和车端面的方法,如金工实习教材第160页所示。
对于既车外圆又车端面的场合,常使用弯头车刀和偏刀来车削端面。弯头车刀是用主切削刃担任切削,适用于车削较大的端面。偏刀从外向里车削端面,是用车外圆时的副切削刃担任切削,副切削刃的前角较小,切削不够轻里向外车削端面,便没有这个缺点,不过工件必须有孔才行。
车端面操作注意点:
(1)安装工件时,要对其外圆及端面找正。
(2)安装车刀时,刀尖应严格对准工件中心,以免端面出现凸台,造成崩坏刀尖。
(3)端面质量要求较高时,最后一刀应由中心向外切削。
(4)车削大端面时,为使车刀准确地横向进给,应将大溜板紧固在床身上,用小刀架调整切削深度。
二、切槽
切槽时用切槽刀。切槽刀前为主切削刃,两测为副切削刃。安装切槽刀,其主切削刃应平行于工件轴线,主刀刃与工件轴线同一高度。
切窄槽,主切削刃宽度等于槽宽,横向走刀一次将槽切出。切宽槽,主切削刃宽度小于槽宽,分几次横向走刀,切出槽宽;切出槽宽后,纵向走刀精车槽底,切完宽槽。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条