1) microetching rate
微蚀速率
2) corrosion rate
腐蚀速率
1.
Research on corrosion rate of sucker rod steel 20Ni2Mo in wet H_2S;
20Ni2Mo抽油杆钢在湿H_2S环境中的腐蚀速率
2.
Description of the corrosion rate of 16Mn pipeline steel in soil by using neural network;
16Mn管道钢土壤腐蚀速率描述的人工神经网络方法
3.
Effect of temperature and pressure on CO_2/H_2S corrosion rate of N80 steel;
温度和压力对N80钢CO_2/H_2S腐蚀速率的影响
3) Corrosion speed
腐蚀速率
1.
First time introduces P_(CO_2)/P_(H_2S) sub pressure to forecast model of tubing steel corrosion speed in order to find out the relation between tubing steel corrosion speed CR and CO_2 sub pressure P_(CO_2)、H_2S sub pressure P_(H_2S).
为了找出油管钢腐蚀速率CR与CO2分压PCO2、H2S分压PH2S之间的关系,首次将分压比PCO2/PH2S引入油管钢腐蚀速率预测模型,在不同分压比下,视一种气体腐蚀为主导,另一种气体腐蚀为影响因素来建立两个分模型,进而将两个分模型叠加,得到总的腐蚀速率预测模型。
4) corrosion velocity
腐蚀速率
1.
While the chipping water applied in the process of circulation cooling water, the average corrosion velocity is 0.
切粒水回用于循环水冷却水系统过程中,腐蚀速率较高,平均为0。
5) Etching rate
蚀刻速率
6) ablation rate
烧蚀速率
1.
Some calculations and analysis for three examples under different ablation rates were demonstrated.
针对金属表面的烧蚀过程,采用一维传热模型,将物体内的传热、温度变化分为2个阶段,即物体被加热到熔点温度的阶段及物体开始烧蚀阶段,使用积分近似的分析方法,完整地建立了表面烧蚀速率与表面加热功率之间的近似计算关系式。
2.
The effects of the respective content of silica aerogel and boron-phenolic resin on the properties of EPDM/NBR flexible insulation material,such as tensile strength,elongation-to-break,mass ablation rate,linear ablation rate and relative density were analyzed and compared.
通过比较分析白炭黑与硼酚醛树脂用量对EPDM/NBR柔性绝热层材料拉伸强度、断裂伸长率、质量烧蚀速率和线烧蚀速率以及相对密度的影响,得出随着白炭黑或硼酚醛树脂用量的增加,柔性绝热层材料的拉伸强度和相对密度呈递增趋势,烧蚀速率呈递减趋势,断裂伸长率在白炭黑和FB用量各自为20份时有极大值。
补充资料：水泵气蚀(见空化与空蚀)
水泵气蚀(见空化与空蚀)
shuibeng qishi水泵气蚀见空化与空蚀。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条