1) Sign vertex
号点
2) point mark
点号
1.
Based on the existing problem of municipal map of the network as well as the current municipal on pipeline management in the data entry system in the course of the analysis,this paper puts forward the method of the consistency checking based on the border-upon domains municipal point mark designation of the network management system and coordinate.
通过对市政管网图的论述以及目前市政管网管理系统在数据录入过程中存在问题的分析,提出了基于临域的市政管网系统中点号与坐标一致性检查的方法,最后利用M apBasic编程,实现了点号与坐标一致性的自动检查与修改。
3) signal dotting
信号打点
1.
In view of the limitation of signal dotting and phonetic communication device used for coal mine,a kind of flameproof signal dotting and phonetic carrier-current communication device especially suited to satisfy the current needs of modernization mine production with high-capacity and high-efficiency is designed,its effects and performance has been validated.
针对目前煤矿使用信号打点、语音通讯装置存在的缺陷,设计出一种能适应当前高产、高效现代化矿井生产需要的煤矿隔爆型信号打点、语音载波通讯装置,其功效和性能已得到验证。
4) punctuation
[英][,pʌŋktʃu'eɪʃn] [美]['pʌŋktʃu'eʃən]
标点符号
1.
The conversion and the similarities and differences of Chinese and English punctuation in English translation for traditional Chinese medicine;
中医英译中汉英标点符号的异同和转换
2.
Analyses on some typical errors in punctuation in English books and periodicals;
英文书刊标点符号典型错误辨析
3.
Comparative Analysis on English-Chinese Punctuation;
汉英标点符号的比较研究
5) vertex labeling
顶点标号
1.
As the definition of vertex labeling and the construction of graphs,the border value of several vertex labeling graphs and the relationship of k and the side number in graceful graphs included K3 are given.
根据图顶点标号的定义以及图形结构,给出几类图的顶点标号的界值限定及包含三角形K3的(k,d)-优美图中边的条数与k的关系。
6) Dot signal
斑点信号
补充资料:闭式单点、双点压力机
| |||||||
主要参数内容 | 国际先进 | 国内先进 | 国内一般 | 国内落后 | 评定方法及说明 | ||
(一)加工精度 | 参照GB10924-89、GB10933-89、JB5200-91 | ||||||
1、滑块下平面对工作台上平面的平行度(mm) | 30%精度储备 | 20%精度储备 | 达到规定值 | 大于规定值 | |||
0.02+0.10/100×滑块下平面的被测长度 | |||||||
2、滑块行程对工作台上平面的垂直度 | 30%精度储备 | 20%精度储备 | 达到规定值 | 大于规定值 | |||
0.05+0.02/100×滑块行程长度 | |||||||
(二)结构性能 | |||||||
1、离合器、制动器接通率,当滑块行程次数≤16次/分时为70%,≤25次/分时为60%,≤45次/分时为50% | 大于规定值10% | 大于规定值 | 达到规定值 | 达不到规定值 | |||
2、液压超负荷保险装置、微调装置、吨位指示器 | 全部具有 | 全部具有 | 部分具有 | 没有 | |||
(三)噪声dB(A) | |||||||
1、公称力≤400kN | ≤85 | ≤87 | ≤88 | >88 | |||
2、公称力>400kN | ≤87 | ≤88 | ≤90 | >90 |
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条