说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 群色散剖面
1)  group dispersion profile
群色散剖面
1.
The propagation characteristics of chirped Gaussian pulses in fibers with 5 different group dispersion profiles are theoretically deduced and the effects of the initial chirps on the pulse width discussed.
文章从理论上推导了啁啾高斯脉冲在5种不同群色散剖面光纤中的传播特性和初始啁啾对脉宽的影响。
2.
The gain spectrum of modulation instability is studied in the condition of decreasing dispersion fiber with different group dispersion profiles.
研究了不同群色散剖面结构的色散缓变光纤中调制不稳定性增益谱。
2)  color gamut section
色域剖面
3)  color profile
彩色剖面
4)  Group velocity dispersion
群速色散
1.
Harmonic generation in BBO by femtosecond laser pulses is studied, taking into account both group velocity mismatch, lowest order group velocity dispersion (GVD) and second order GVD.
同时考虑了群速色散失配、最低阶群速色散(GVD)和二阶群速色散。
2.
An existence of an region of anomalous group velocity dispersion (GVD) span near (550 ̄700) nm band was evidently indicated.
通过对PPQ薄膜的吸收光谱的计算分析,由Kramers-Kronig关系得出PPQ膜在550nm~700nm左右波段存在负群速色散区,并且色散量相对较小,|β2|<1。
3.
A novel second-harmonic generation scheme is proposed to compensate group velocity dispersion effects.
提出了一种啁啾补偿群速色散的倍频方法,通过向入射基频光引入合适的初始啁啾,让其与色散相互作用,以实现对基频光脉冲宽度的主动控制,提高转换效率。
5)  group dispersion
群色散
6)  group-velocity dispersion
群速色散
1.
The combined effects of self-phase modulation, positive group-velocity dispersion and stimulated Raman scattering through 15ps 1.
06μm的Nd:YAG激光脉冲在单模光纤中传输时,光纤中自相位调制(SPM),正群速色散(GVD)和受激喇曼散射(SRS)引起的联合非线性效应。
补充资料:关于solidworks 中的剖面线中的剖面线

solidworks的剖面线线型定义和autocad相同,它使用了autocad的剖面线定义方法,与autocad通用.因此,可以对剖面线进行定义.


方法:修改\SolidWorks\lang\chinese-simplified\sldwks.prn


用笔记本打开该文件,添加需要的线形.如


;; Based on AutoCAD Ver.13.0s Hatch Pattern File


;;;; solidworks 区域剖面线定义文件 ::


*金属, (Iron BrickStone), ANSI Iron, Brick, Stone masonry


45, 0,0, 0,.125


*塑料, (Lead Zinc Mg), ANSI Lead, Zinc, Magnesium, Sound/Heat/Elec Insulation


45, 0,0, 0,.125


135, 0,0, 0,.125


*玻璃,AR-GLASS@1.0


45,0,0,0,0.5, 0.5,-0.5


45,0,0.1414214, 0,0.5, 0.3,-0.7


45,0.1414214,0, 0,0.5, 0.3,-0.7


*软木, Cork material@1.0


0, 0,0, 0,.125


135, .0625,-.0625, 0,.35355339, .176776696,-.176776696


135, .09375,-.0625, 0,.35355339, .176776696,-.176776696


135, .125,-.0625, 0,.35355339, .176776696,-.176776696


*无, None


删除不需要的定义类型,可以大大提高solidworks 的启动速度

说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条