1) joining width
搭接宽度
1.
For the circular-hole damage in the high stress zone of wing integral panel,it uses the different joining width to compute the glued joint repair of the damage integral panel.
为了准确模拟损伤部位的局部位移和力边界条件,基于某飞机的全机有限元模型,对机翼整体壁板高应力区的圆孔型损伤,采用不同搭接宽度计算了受损壁板的胶接修理。
2) apparent connection length
视搭接宽度
1.
Two different plans of apparent connection length between near pile are briefly contrasted and analyzed.
简要地对比分析了相邻桩之间不同视搭接宽度的两种方案。
3) lap length
搭接长度
1.
The stitching joint 3D braided composites with various stitching direction,lap length and stitching density were experimentally studied to reveal the effect of stitching parameters on the tensile property.
研究了多种缝合方向、搭接长度和缝合密度对缝合连接三维编织复合材料拉伸性能的影响,并与三维整体编织复合材料的拉伸性能进行对比。
2.
The graph of tensile strength and lap length is presented and a method of defining the relationship of tensile shear strength and lap length is put forward.
为了研究单搭接接头承载能力与搭接长度的定量关系,对不同搭接长度的单搭接接头进行了有限元分析,得到了单搭接接头承载能力与搭接长度的关系曲线图。
3.
Effect of the lap length on stress distribution in weldbonded joints has been analysed numerically using three dimensional elastoplastic finite element method (FEM).
采用三维弹塑性有限元方法，对采用酚醛树脂和丙烯酸酯两种结构胶粘剂的胶焊单搭接头，研究了其搭接长度对接头中应力分布的影响。
4) overlap height
搭接高度
1.
Analysis of overlap height of tail tube in side track well;
侧钻水平井尾管搭接高度分析
5) overlap length
搭接长度
1.
In this paper,the overlap length of single-lap joint reinforced by z-pins is 15mm,20mm,23mm,37mm and 60mm,respectively.
本文对搭接长度分别为15mm,20mm,23mm,37mm,60mm的Z-pins增强陶瓷基复合材料接头在单向载荷作用下的连接性能进行了试验研究和数值模拟。
6) overlapping length
搭接长度
1.
The influence to bondingstrength between steel pipe and concrete core with different overlapping length and different UEA content is discussed, and the formulae for calculating the bonding length of concrete core .
依托深圳蛇口集装箱码头二期工程,进行了钢管桩与混凝土芯粘结力及抗弯应力传递模拟试验,对试验结果进行理论分析,讨论了不同搭接长度和不同UEA掺量对钢管桩与混凝土芯单位粘结力的影响;推导出纯弯矩作用下,混凝土芯与钢管粘结段粘结长度的计算公式。
补充资料：黏合搭接接头
分子式：
CAS号：
性质：两个被粘物部分叠合粘接在一起形成的接头。搭接比对接形式抗剪强度高，而且可靠，是一种十分普遍使用的粘接形式。
CAS号：
性质：两个被粘物部分叠合粘接在一起形成的接头。搭接比对接形式抗剪强度高，而且可靠，是一种十分普遍使用的粘接形式。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条