1) apparent stiffness
表观刚度
2) micro stiffness
细观刚度
1.
In this article,a finite element method (FEM) of filament-wound composites is developed which is based on the micro stiffness model of a filament-wound composite.
发展了一种缠绕复合材料结构分析有限元方法,该方法基于缠绕复合材料细观刚度模型,通过建立细观刚度场与整体结构的映射关系,将缠绕复合材料细观刚度模型引入缠绕复合材料结构有限元分析中。
3) ground surface stiffness
地表刚度
1.
The deformation principles of the foundation pit due to unsymmetrical load, dewatering, ground surface stiffness, digging range and time are analyzed.
通过对南京地铁明挖段基坑工程变形情况进行分析,指出狭长条形基坑的变形特征,并分析不均匀超载、降水、地表刚度、开挖范围及开挖时间对基坑变形的影响规律,提出相应的控制基坑变形的工程措施。
4) apparent viscosity
表观黏度
1.
Study on the method for measuring the apparent viscosity of oil-coal slurry;
油煤浆表观黏度测量方法的研究
2.
Model for predicting apparent viscosity of the microfiltration concentrated broth of Bacillus thuringiensis;
苏云金芽胞杆菌微滤浓缩液表观黏度模型
3.
Study on the apparent viscosity and microstructure of semi-solid Al - Si alloy prepared by chemical refining;
化学细化半固态Al-Si合金表观黏度及组织分析
5) viscosity
[英][vis'kɔsiti] [美][vɪs'kɑsətɪ]
表观粘度
1.
The dependence of the solution shear viscosity on the shear stress,temperature and cellulose material content was investigated.
考察了剪切力、温度、纤维素原料质量分数对溶液表观粘度的影响。
2.
Abstact:In the thesis the rheology of trigonella bean gum was studied by studying the apparent viscosity changing affectedby concentration, shearing, temperature, pH, freazing-thawing and synergic effect with xanthan gum.
通过测定和分析浓度、剪切力、温度、pH和冻融等变化对葫芦巴胶溶液表观粘度的影响及与黄原胶等食品胶的协效性,对葫芦巴胶溶液的流变性进行了研究。
3.
The results show that the viscosity of blends is lower than that of pure PSU.
研究发现，共混体系的表观粘度均低于纯聚砜体系的粘度。
6) apparent viscosity
表观粘度
1.
Experimental investigation on apparent viscosity of heavy oil-water two-phase flow in horizontal pipe;
稠油-水二相水平管流表观粘度的实验研究
2.
Influence of technological parameters on apparent viscosity of semi-solid magnesium alloy;
工艺参数对半固态镁合金表观粘度的影响
3.
Study on photooxidation aging apparent viscosity of asphalt
光氧老化对沥青表观粘度的影响
补充资料：JPZ型三向等刚度橡胶减震器
分子式：
CAS号：
性质：JPZ-type tridirective equal rigid rubber mounting 橡胶减震器的一种。具有x、y、z三个方向等刚度、等自震频率。按负荷大小可分为JPZ-1、JPZ-2两种型号。由中央金属芯柱、伞形金属罩及橡胶连接而成，模压法生产。可满足导弹控制仪等设备的隔震和抗冲击要求。
CAS号：
性质：JPZ-type tridirective equal rigid rubber mounting 橡胶减震器的一种。具有x、y、z三个方向等刚度、等自震频率。按负荷大小可分为JPZ-1、JPZ-2两种型号。由中央金属芯柱、伞形金属罩及橡胶连接而成，模压法生产。可满足导弹控制仪等设备的隔震和抗冲击要求。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条