说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 膜缝灌
1)  film silt irrigation
膜缝灌
1.
Based on a number of infiltration experiments on wheat film silt irrigation and onedimensional vertical infiltration,the effects of film silt width and initial soil moisture content on the infiltration parameters were analyzed in this paper.
膜缝灌是一种新的灌水技术,其应用理论基础尚有待进一步研究。
2)  irrigation through membrane crack
膜缝灌溉
3)  film crack border irrigation
膜缝畦灌
1.
By analyzed the test date of winter wheat film crack irrigation technology, the optimum comprehensive technical parameter of film crack border irrigation is presented according to irrigation efficiency distribution uniformity and store water efficiency.
通过对冬小麦膜缝灌水技术试验的资料分析,确定出灌水效率、灌水均匀度、储水效率均较高的膜缝畦灌的最佳技术参数组合,为冬小麦膜缝畦灌提供技术指导。
4)  film slit furrow irrigation
膜缝沟灌
1.
Study on the effect of ecological environment and crop of summer maize under film slit furrow irrigation
膜缝沟灌对夏玉米生态环境及作物效应研究
5)  crack pouring
灌缝
1.
The application of crack pouring and bored grouting in concrete pavement maintenance;
灌缝和钻孔压浆在混凝土路面养护中的应用
2.
Hamesing of crack disease of bituminous pavement was also introduced acording to cracks practical situation and crack pourings practice in few years.
本文介绍了高速公路沥青路面裂缝这一早期病害现象,分析了其产生的原因及危害性,结合目前我省高速公路路面裂缝的实际情况和近几年的灌缝实地经验,简要介绍了我省沥青路面裂缝的处治措施。
3.
Combining with the raw material and production technology of common-temperature colophony asphalt pavement developed according to the highway maintenance experience of several years, crack pouring materials are conducted test appraisal in aspects of crack resistance under low temperature, adherence and stability under high temperature.
根据多年公路养护经验而开发生产的常温树脂类沥青路面裂缝灌缝材料的原材料及制作工艺,对该灌缝材料的低温抗裂性、粘附抗脱性、高温稳定性等性能进行测试评价,并提出常温树脂类沥青路面裂缝灌缝的施工建议,对该灌缝材料的应用推广具有重要意义。
6)  saw to sew and infuse to sew
锯缝与灌缝
补充资料:电解食盐水溶液离子膜电解槽所用的膜材料之一
分子式:
CAS号:

性质:又称全氟羧酸-磺酸复合离子膜  Rf-COOH-Rf-SO3H  电解食盐水溶液离子膜电解槽所用的膜材料之一。使用时,将较薄的羧酸层面向阴极,较厚的磺酸层面向阳极,因而兼有羧酸膜和磺酸膜的优点。由于Rf-COOH层的存在,可阻挡氢氧离子返迁移到阳极室,确保了高的电流效率(96%),因Rf-SO3层的电阻低,能在高电流密度下运行,且阴极液可用盐酸中和,产品氯气中氧含量低,氢氧化钠浓度可达33%~35%。可在全氟磺酸膜上涂敷一层全氟羧酸的聚合物,或是将磺酸膜和羧酸膜进行层压,或是采用化学方法处理而制得的复合膜。现以采用化学方法处理者质量最佳。

说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条