1) metal melting trace
金属熔痕
2) trace metal
痕量金属
1.
The influence of wind-wave disturbance on colloidal trace metals in the waters of Taihu Lake.;
风浪扰动对太湖水体中胶体态痕量金属含量的影响
2.
The exchange adsorption mechanism effect of trace metal on syspended particles;
痕量金属在悬浮颗粒物上的吸附交换机理
3.
A summarization of the interaction of colloidal particles and trace metal in natural water;
天然水体中胶体粒子与痕量金属相互作用研究
3) trace metals
痕量金属
1.
Development of flow injection-chemiluminescence method in determination of trace metals;
流动注射化学发光法测定痕量金属元素的进展
2.
The different supplement dosage of trace metals Fe,Co,Ni on the improvement of the anaerobic digestion of Solid Waste from farming trade market is studied.
在完全混合工艺条件下对农贸市场的固体废弃物进行厌氧消化,分析消化过程中pH值、VFA(挥发性脂肪酸)、COD(化学需氧量)和产气量等随时间的变化情况,研究不同投加量的痕量金属Fe、Co、Ni对农贸市场固体废弃物厌氧消化的促进作用。
3.
Based on correlation coefficients and principal component analysis, Fe and Al were selected as the concentration normalizer for the different trace metals.
由相关系数和主成份分析 ,选择铁和铝作为沉积物中痕量金属浓度的均一化元素 。
4) deposited metal
熔敷金属
1.
Influence of gas content on impact toughness of deposited metal of martensitic stainless steel;
气体含量对马氏体不锈钢熔敷金属冲击性能的影响
2.
Effects of nonmetallic inclusions on acicular ferrite nucleation in deposited metals of microalloyed steel;
夹杂物对微合金钢熔敷金属针状铁素体形核的影响
3.
Research of M-A component in 9%Cr-1%Mo deposited metal;
9%Cr-1%Mo耐热钢熔敷金属中M-A组元的研究
5) Metal molten pool
金属熔池
1.
Research into the numerical simulation of the influence of the depth of slag pool on the metal molten pool during the ESR;
电渣熔铸过程渣池深度对金属熔池影响的数值模拟研究
6) deposit metal
熔敷金属
1.
According to the introduction of the manufacture process feature of flux-cored wires and the good performances exhibited by the deposit metal,the current questions on the popularization and application of flux-cored wires were analyzed,as well as the applied methods of flux-cored wires for manual welding.
通过对药芯焊丝制造工艺特点及其熔敷金属所表现出的良好性能的介绍,分析了当前药芯焊丝推广应用所遇到的问题,提出了将药芯焊丝用于手工焊接的方法,并指出了推广应用的几个关键问题。
补充资料：熔接痕
分子式：
CAS号：
性质：又称熔接缝，熔接痕，汇流纹，汇合纹等，是在模塑制品表面，由两股或多股物料流在一起形成的条痕，是由于模塑或注塑时两股或多股料流在相遇的界面处未完全熔合所致。
CAS号：
性质：又称熔接缝，熔接痕，汇流纹，汇合纹等，是在模塑制品表面，由两股或多股物料流在一起形成的条痕，是由于模塑或注塑时两股或多股料流在相遇的界面处未完全熔合所致。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条