1)  air flux
空气流
1.
The air flux was then thought equal entropy flux, therefore the mathematical model was obtained.
此时把空气流看作等熵流动 ,从而得出数学模型。
2)  Air flow field
空气流场
1.
this paper gives a brief introduction to the numberical calulation of air flow field around moving vehicle with finite-volume method concerning basic equations,the application of finite-volume method,crisscross network and the treatment of boundary condition.
介绍了汽车运动空气流场数值计算的有限容积法的主要内容，涉及基本方程、有限容积法的应用、交错网格系统及边界条件的处理等，并给出了应用算例，建立了汽车运动流场数值计算的理论基础。
3)  air velocity
空气流速
1.
Impact of Indoor Air Velocity on Physiological Index and Thermal Comfort;
室内空气流速对人体生理指标及热舒适性影响的研究
2.
As results,air velocity,water-air ratio and ini-tial water temperature are significant,especially mutual actions between air velocity and otherfactors.
结果表明,空气流速 V、水气比μ、和喷水初温等是影响喷水室热湿交换的主要因素;空气流速V 和诸因素的交互作用对喷水室热湿交换有着显著影响;对不同风速范围内,喷排布置的间距取值提出了建议。
3.
This article analyses and illustrates the source as well as assessment of the first standard air velocity measurement uncertainty.
本文就空气流速一等标准装置测量不确定度的来源及评定进行了分析与说明,并分别对A类与B类不确定度的产生和计算过程进行了详细的介绍。
4)  air flow
空气流量
1.
In order to solve these problems,this paper analyzed the application of the multi-sensors information fusion technology in air flow test system and proposed a way to design multi-sensors air flue test system based on LabVIEW.
在传统的空气流量测试系统中,存在着测试精度低、工作量大等问题。
2.
In order to keep the stability of idle speed with better control for the air flow in idle speed mode,a driver circuit of stepper motor is designed in this paper,according to the working theory of idle control device using stepper motor,and the idle device is controlled by a board based Digital Signal Processor(DSP) which integrates the driver circuit.
为了更好地控制怠速空气流量,以保持发动机的怠速稳定性,根据步进电机式怠速控制阀的工作原理设计了步进电机的驱动电路,并使用基于数字信号处理器(DSP)的已集成该驱动电路的控制电路板对怠速阀进行控制。
5)  air flow
空气流动
1.
The numerical simulation of air flow in electric power plant with internal combustion engine room;
内燃机电站机房内空气流动的数值模拟
2.
Numerical simulation of multi-channel air flow and thermal performance in warm air unit used for different altitude zones;
变地域暖风机多通道空气流动数值模拟及换热性能分析
3.
Mastering the air flow and heat transfer condition in engine compartment of tank is an essential precondition for designing engine device,transmission device and cooling system rationally.
掌握坦克动力舱内空气流动与传热状况,是合理设计其动力装置、传动装置和冷却系统的必要前提和重要环节。
6)  airflow field
空气流场
1.
Numerical simulation of airflow field in ship cabin;
船艇机舱空气流场数值模拟研究
2.
In order to predicte and analyze the rationality of cooling system in the virtual engine compartment,the numerical simulation of airflow fields in the engine compartment by using computational fluid dynamics(CFD) technique is necessary.
将装甲车由机械传动改为电传动后,电机类设备的增加对动力舱内的冷却系统提出新的要求,利用计算流体动力学(CFD)技术对虚拟动力舱内空气流场进行数值模拟,可以对动力舱冷却系统的合理性进行预测分析并提出建议。
参考词条
补充资料：6-2L压缩空气冲锤操作规程
1、遵守铸造设备通用操作规程。
2、工作前检查伐门手柄是否处于静止的位置。
3、拧开压缩空气冲伐，然后进行试车；试车时，伐门开得小一点，冲锤不要空打在设备上。确认一切正常后，方可进行生产。
4、工作时，把需要冲击的部位正放在冲头下面，不要歪斜，以免发生人身事故。
5、操作冲头伐门时不要使冲头一冲到底，要往返冲击几次。
6、工作后，要把伐门手柄放在静止的位置上，然后关闭总伐。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。