1) directional gap probability
方向间隙率
2) radial clearance
径向间隙
1.
The influence of radial clearance of sliding bearing on superheat failure of bearing Liang Baoying;
滑动轴承径向间隙对轴承过热故障的影响
2.
The radial clearance of tLhe big joumal bearing in rock bit's bearing system is of great importance to the service behavior of the bit.
从润滑理论的分析表明，最小油膜厚度随半径间隙变化的幅度很小；从接触力学理论的分析表明，适当减小径向间隙值，可以降低轴承接触压力峰值；从摩擦发热角度的分析表明，减小配合间隙可以降低摩擦发热和磨损量；普通合金钢滑动轴承半径间隙值不小于0。
3.
Taking the manufacture clearance into consideration under the special torque load and a constant speed,the right radial clearance of roller bearing is solved out through selecting among roller bearings with different radial clearances and making a summary of the analyzing results.
在一定转速和载荷作用下,通过选取不同的滚针轴承径向间隙,并考虑加工情况进行分析计算,对结果进行总结,找出适合的行星齿轮滚针轴承径向间隙,并在试验中进行了验证。
3) Backlash
[英]['bæklæʃ] [美]['bæk'læʃ]
反向间隙
1.
Backlash Compensation of Half-closed CNC Machine Tools Based on Acceleration and Deceleration Control;
基于加减速控制的半闭环数控机床反向间隙补偿
2.
The results of simulation on backlash verify the effect iveness of this methodology.
仿真结果表明可以较好地解决反向间隙等非线性的控制问
3.
At present each kind of traditional reduction gears has the backlash in the market, with difficult compensates, which reduces the operation precision of robot.
本课题主要针对反向间隙问题提出一种无反向间隙变速机构,主要用于机器人回转关节,由于采用滚珠丝杠-预紧螺母机构,它不存在返程间隙,具有传动精度高,结构简单,制造方便等优点。
4) reverse gap
反向间隙
1.
The causes which occur from the reverse gap were introduced,and the influences of reverse gap were analyzed from the example of concrete processing.
对反向间隙产生的原因进行了介绍,并举出具体的加工实例来分析、说明反向间隙对数控加工产生的影响,指出了反向间隙补偿的一般方法和步骤。
2.
Error processing machine is not totally avoided, but we can take effective measures to control In this paper, the causes for the reverse gap are introduced; specific examples are given to analyze to illustrate the reverse gap impact to NC machining producing.
本文对反向间隙产生的原因进行了介绍,举出具体的加工实例来分析、说明反向间隙对数控加工产生的影响,同时指出了减小和控制反向间隙的一般方法和步骤。
5) axial clearance
轴向间隙
1.
Analysis the producing ways of axial clearance of bent axises on X195 diesel;
保证X195柴油机曲轴总成轴向间隙几种生产方式的讨论
2.
The method of eliminating axial clearance,logical fixing configuration and effective guard of ballscrew nut pair are all introduced in this paper.
介绍滚珠丝杆螺母副轴向间隙的消除方法、合理的安装结构和有效的防护装置。
3.
It was found that these faults were attributed to(1) the excess axial clearance of the rolls at the bearing seat,and(2) the excess bouncing resulting from the unbalanced force applied to the rubber mat of the rolls.
经分析,原因是轧辊非传动端轴承座装配的轴向间隙过大,且螺纹公差偏大,所以造成轧辊窜动严重以及原用胶垫受力不均衡,弹跳过大。
补充资料：电导率(见电阻率)
电导率(见电阻率)
conductivity
d!日nd日O}已电导率(eonduetivity)见电阻率。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条