1) Sinking a well to irrigate crop
打井补灌
2) well-irrigation
井灌
1.
Suitable well-irrigation is about 80% of the total farmland area in north Huaihe River plain of Anhui province.
安徽淮北平原宜井灌溉面积占总耕地面积近80%。
3) well irrigation
井灌
1.
The question existing in well irrigation used in Guzhen county and countermeasure;
固镇县发展井灌存在的问题及对策
2.
Application of water temperature simulation model in sunning water tank for well irrigation rice area;
水温模拟模型在井灌水稻区晒水池中的应用
3.
Application of gray system theoryin water temperature forecast for well irrigation rice area;
灰色系统理论在井灌水稻区渠道水温预测中的应用
4) filling the hole
灌井
5) supplemental irrigation
补灌
1.
Effects of supplemental irrigation on pumpkin with film mulching and planting in furrow in the agro-pastoral ecotone of north China;
华北农牧交错区覆膜沟作小南瓜的补灌效应
6) supplementary irrigation
补灌
1.
Research on developing characteristics of winter wheat/corn intercropping systems with supplementary irrigation of catchment water;
集雨补灌对冬小麦套玉米复合群体生长特性研究
2.
Based on on-farm observations and experiments, SWAP Model was used to analyze the seasonal variation of soil salt and impact of groundwater table on the distribution of soil salt under conditions of drainage water reuse in Bojili Irrigation District in the lower reaches of the Yellow River, and simulate the effect of supplementary irrigation by surface drainage water on crop s yield.
在田间试验观测基础上,采用SWAP模型分析黄河下游簸箕李引黄灌区农田排水再利用下的土壤盐分季节性变化以及地下水位对土壤盐分剖面分布的影响,模拟农田排水补灌对作物产量的效应。
3.
Collecting rainwater in fallow period and carrying out supplementary irrigation in crop growing season is a effective measure to improve yield.
收集的雨水应按照作物灌溉制度,以圆艺作物为主要供水对象,大田作物上补灌应以稀植作物为主,密植作物为辅。
补充资料：补片教程－补六边缺口
补此面的方法：
1、insert /points set/points on curve/
选项中number of points 选的越大，补出的面质量越高
2、insert /free form feature /from point cloud
选择上部插入的点，作出补丁面
3，insert /form feature /extract curve
从空缺多边形的边缘提取出曲线
4、insert /form feature /extruded body
沿垂直曲面方向（此处可用草图建模作方向线）
拉伸上述曲线，制作切割工具面
5、insert /form feature /trimmed sheet
用上步拉伸的曲面切割上面作出的补丁面
6，inser feature operation / sew
缝合 that is all .
1、insert /points set/points on curve/
选项中number of points 选的越大，补出的面质量越高
2、insert /free form feature /from point cloud
选择上部插入的点，作出补丁面
3，insert /form feature /extract curve
从空缺多边形的边缘提取出曲线
4、insert /form feature /extruded body
沿垂直曲面方向（此处可用草图建模作方向线）
拉伸上述曲线，制作切割工具面
5、insert /form feature /trimmed sheet
用上步拉伸的曲面切割上面作出的补丁面
6，inser feature operation / sew
缝合 that is all .
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条