1) Weighing sensor
称量传感器
1.
This paper mainly introduces the operating principle and action of weighing sensor and velocity measurement sensor according to the electronic belt balance weighing procedure,and brings forward their common problems.
根据电子皮带秤的工艺过程,介绍了称量传感器和测速传感器的工作原理和作用,并提出了其常见问题的处理方法。
2) weighing transducer /sensor
重量传感器;称重传感器
3) weighing transducer
称重传感器
1.
Nonlinear compensation of capacitance weighing transducer based on inverse fitting;
基于反拟合法的电容称重传感器非线性校正
2.
Research on cylindrical capacitance weighing transducer with variable distance between electrodes;
柱式变极距电容称重传感器研究
3.
Its principle is to add the loading control anchor gate to the underground coal slot and tiger anchor gate, adopting imported hydraulic weighing transducer to survey the weight, besides, realizing the main control through PLC, which then realizes the automatic fixed weight loading of the old main well.
其原理是对井下溜煤槽、老虎闸增加装载控制闸门,采用进口液压称重传感器测重,并通过PLC可编程控制器来实现主控制,从而实现老主井的自动化定重装载。
4) weighing sensor
称重传感器
1.
Signal Acquiring and Processing of Digital Weighing Sensor;
数字称重传感器的信号获取及处理
2.
Load-bearing Characteristics of the Quartz Resonant Weighing Sensor;
石英谐振式称重传感器的承载特点分析
3.
An Adaptive Dynamic Compensation Method for Weighing Sensor;
称重传感器自适应动态补偿方法
5) load cell
称重传感器
1.
Shaft pin type load cell and its application;
轴销式称重传感器及其应用
2.
Dynamic characteristics of strain gauge load cell;
应变式称重传感器的动态特性
3.
Discussion about design methods of load cell elastic solid finite element;
称重传感器弹性体有限元设计方法的探讨
6) weighting sensor
称重传感器
1.
Dynamical compensating method for weighting sensor based on FLANN;
基于FLANN的称重传感器动态补偿方法
2.
Buffering performance of the hydraulic weighting sensor
液压称重传感器缓冲性能的研究
3.
This article designs an intelligent cars weighting system with MSC1210 MCU, 8 channels analog weighting sensor single collection, RS232 serial port to communicate with MWD.
本文以MSC1210微处理器为核心,对8路模拟称重传感器信号的采集,通过RS232接口与上位机进行通信,构成一个智能汽车称重系统。
补充资料：变压器式传感器
利用变压器作用原理把被测位移转换为初、次级线圈互感变化的变磁阻式传感器。它由两个或多个带铁心的线圈构成，初、次级线圈间的互感能随衔铁或两个线圈间的相对移动而改变。当用适当频率的电压激励初级线圈时,次级线圈的输出电压将随互感的改变而变化,从而将被测位移转换为电压输出。这种传感器在使用中常采取两个同名端串接的次级绕组线圈，以差动方式输出，所以又称为差动变压器式传感器。变压器式传感器的特点与电感式传感器相同，有时亦称电感式传感器。但变压器式传感器在设计上具有更大的灵活性，应用更为广泛。旋转变压器、感应同步器、自整角机都属于变压器式传感器。变压器式传感器主要用于测量位移和能转换成位移量的力、张力、压力、压差、加速度、应变、流量、厚度、比重、转矩等参量。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条