1) cold shock treatment
冷冲击
1.
The effect of cold shock treatments on quality of nai-plum (Prunus salicina Lindl.
以柰李为试材,采用冷冲击处理对柰李低温贮藏品质的影响进行试验。
2) TI
冷冲击强度
3) cold shock treatment
冷冲击处理
1.
Through comparing the variations of their contents after different cold shock treatments and the chilling injuries (CI), the regularity of phytohormone variations and the relationship between phytohormones level and the chilling tolerance of Nai-plum fruits during the cold storage were discussed.
通过比较了不同冷冲击处理对内源激素的影响以及贮藏过程中激素的变化,并结合冷藏过程中冷害发生情况,初步探讨了各处理在冷藏过程中内源激素变化的规律及其与柰李果实抗冷性的影响。
2.
The results showed that cold shock treatment refrained desiccation, and the degree of refrainment was increasing with the duration of cold shock treatment.
）为材料，以０℃的冰水混合物为冷却介质，研究了不同冷冲击处理（１ｈ，２ｈ，３ｈ，４ｈ）对贮藏期间银杏硬化的影响结果表明，冷冲击处理能显著地控制白果的硬化，硬化率随处理时间的延长而降低
3.
The experiment showed that cold shock treat-ment refrained the activity of polygalacturonase,and the degree of refrainment was increasingwith the time of cold shock treatment.
本实验以绿熟期的渝抗二号番茄（ＶａｒＣｏｍｍｕｎｅｂａｉｌｅｙ）为材料，０℃的冰水混合物为冷却介质，研究了不同冷冲击处理时间（１ｈ，２ｈ，３ｈ，４ｈ）对贮藏期间多聚半乳糖醛酸酶（ＰＧ）活性的影响。
4) cool punch
冷冲头
5) punches
冷冲凸模
1.
This paper,based on the main and failure types of cold blunt mold,such as cotlapsing,worn-away and splitting,studies the durability of fatigue failure of punches.
基于崩刃、刃口磨损、断裂等冷冲模的主要失效形式,探讨了冷冲凸模的疲劳折断耐用度,并提出了提高其耐用度的几种措施。
6) cold punching die
冷冲模
1.
In order to change lower service life and falure of Cr12 stainless steel gasket cold punching die, using DGJW45 steel-bonded hard alloy and B-V compound intensifying processing, die life was enhanced 20~25 times.
为改变Cr12型电炉钢制不锈钢垫圈冷冲模使用寿命短、早期失效等现象,选用DGJW45钢结硬质合金新型模具材料和采用硼-钒(B-V)复合强化处理,模具寿命提高20￣25倍。
2.
The failure cause was analyzed and the heat treatment process was improved was improved for silicon steel cold punching die.
对硅钢片冷冲模进行了失效分析且对其热处理工艺进行了改进,实践证明:改进锻造工艺及淬火后采用深冷处理等方法可显著提高模具的使用寿命。
3.
It is the key to the die producing to increase the service life of the cold punching die.
提高冷冲模使用寿命是模具制造的重点 ,因此提出几种工艺改进措施。
参考词条
补充资料：冲击挤压(见冷挤压)
冲击挤压(见冷挤压)
impact extrusion
ehongji jiya冲击挤压(impaet extrusion)见冷挤压。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。