说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 单点源入渗
1)  single point source infiltration
单点源入渗
1.
Thereby two single point source infiltration models including the side infiltration .
通过室内膜孔单点源入渗试验,分析了膜孔灌单点源入渗单位面积侧渗量与一维垂直入渗量的变化规律,研究了膜孔灌单点源入渗单位面积侧渗量与入渗时间、膜孔直径之间的关系,建立了包含垂直一维入渗量和侧渗量的两个具有明确物理意义的膜孔单点源入渗模型,只需知道垂直一维入渗参数、膜孔直径和入渗时间,即可用于膜孔单点源入渗量的计算。
2)  single film hole point source infiltration
单膜孔点源入渗
3)  point source infiltration
点源入渗
1.
Research advances of point source infiltration under film hole irrigation with sufficient water supply;
膜孔灌充分供水点源入渗研究进展
2.
The influence of soil texture bulk density and water applied methods on point source infiltration;
土壤质地、密度及供水方式对点源入渗特性的影响
3.
The mathematics simulation models of point source infiltration interrelated with drip irrigation water dynamic are summarized,and the structure,characteristic and problem of analytical model,numerical model and empirical model are discussed.
就与滴灌水分动态密切相关的点源入渗过程的数学模拟方法进行了综述,对解析解、数值解和经验解的结构、特点及主要存在的问题进行了论述,并介绍了考虑作物根系吸水的滴灌入渗水分运动模型。
4)  point source infiltration parameter
点源入渗参数
1.
Determination of point source infiltration parameters based on Kostiakov model with field irrigation data in film hole irrigation;
由膜孔灌田面灌水参数推求基于Kostiakov模型的点源入渗参数
2.
This paper studies the behaviors of water flow advance process based on field experimental data, and suggests the film hole infiltration model based on the Kostiakov infiltration equation, and presents a new method of determining single point source infiltration parameters under adequate water supply in film hole irrigation.
根据膜孔畦灌大田灌水试验实测资料,研究了膜上水流推进规律,并对膜孔入渗采用Kostiakov入渗模型,提出利用膜孔畦灌田面水流推进和观测断面水深资料推求充分供水条件下点源入渗参数的新方法。
5)  point source infiltration model
点源入渗模型
6)  without restrict point-source infiltration
自由点源入渗
1.
Indoor experiment on measurement of soil hydraulic parameter using the method without restrict point-source infiltration;
利用自由点源入渗法测定土壤导水参数的室内试验
补充资料:闭式单点、双点压力机
代码:00413
设备名称:闭式单点、双点压力机
型号规格:公称力≥800kN
计量单位:台
主要参数内容
国际先进国内先进国内一般国内落后评定方法及说明
(一)加工精度
    参照GB10924-89、GB10933-89、JB5200-91
1、滑块下平面对工作台上平面的平行度(mm)
30%精度储备20%精度储备达到规定值大于规定值 
0.02+0.10/100×滑块下平面的被测长度
     
2、滑块行程对工作台上平面的垂直度
30%精度储备20%精度储备达到规定值大于规定值 
0.05+0.02/100×滑块行程长度
     
(二)结构性能
     
1、离合器、制动器接通率,当滑块行程次数≤16次/分时为70%,≤25次/分时为60%,≤45次/分时为50%
大于规定值10%大于规定值达到规定值达不到规定值 
2、液压超负荷保险装置、微调装置、吨位指示器
全部具有全部具有部分具有没有 
(三)噪声dB(A)
     
1、公称力≤400kN
≤85≤87≤88>88 
2、公称力>400kN
≤87≤88≤90>90 
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条