1) cutting resistance
切削阻力
1.
The results testified the feasibility of the cutting mechanism and showed the sequences of test factors according to the influence on cutting resistance and cutting-out ra.
试验结果检验该半旋转切削机构的可行性及分析得出了影响切削阻力试验指标和切削成功率试验指标的主、次试验因素。
2.
The result of experimentation can be expressed as follows:The cutting resistance increasing rapidly in the beginning of cutting into the stock,it comes to the max when cutting about 2mm into the stock,then decreasing slowly.
实验表明:切削阻力在进入砧木初期迅速增大,在切深2mm左右达到最大,以后逐渐减小;切削阻力在试验条件下小于300N。
3.
On the basis of experiments, the experimental results show the limitedload of anti-compression, the highest cutting resistance and the minimum cutting line-speed, and show that the diameter of se.
试验结果得出毛桃树苗抗压伤极限载荷、毛桃苗切削最大阻力和刀片的最小极限切削线速度;以及影响毛桃苗切削的因素关系,苗木直径、转速、滑切角依次影响切削阻力大小,苗木直径与切削阻力呈平方关系;转速与切削阻力呈线性关系;滑切角与切削阻力也呈线性关系。
2) Milling Resistance Torsion
切削阻力矩
1.
Toll s arrangement Style of Pavemill and Calculation of Milling Resistance Torsion;
路面铣削装置的刀具排列形式与切削阻力矩计算
3) Wood cutting resistance
木材切削阻力
4) heavy cut
重切削，强力切削
5) cutting force
切削力
1.
Study on the friction coefficient of PCBN compact based on cutting force;
基于切削力的PCBN复合片表面摩擦系数研究
2.
Study on Cutting Force and Tool Life in Ti6Al4V High Speed;
硬质合金刀具高速干车削Ti6Al4V切削力及刀具寿命研究
3.
Study on Tool Wear and Cutting Force of Cemented Carbides in Milling Ti6Al4V;
硬质合金刀具铣削Ti6Al4V时刀具磨损及切削力研究
6) milling force
切削力
1.
The morphology of the chips and the milling forces at various speeds were investigated.
使用直径为12mm的TiAlN涂层整体圆柱立铣刀,以151~942m/min的切削速度,对硬度为HRC41的P20淬硬钢进行了高速铣削试验,考察了各种切削速度下的切屑形态和切削力。
2.
The empirical model for the prediction of milling forces in high speed end milling of 1Cr18Ni9 corrosion resistant steel is developed.
基于概率统计和回归分析原理,对回归方程进行了显著性检验,并建立了1Cr18Ni9不锈钢的切削力经验模型。
3.
The morphology of the chips,chip microhardness,chipping temperature,and the milling forces at various speeds are investigated.
使用TiAlN涂层整体圆柱立铣刀,对P20淬硬钢(41HRC,32HRC)进行了高速铣削试验,考察了各种切削速度下的切屑变形、微观硬度、切削温度和切削力。
补充资料：肺循环阻力(或全肺阻力)
肺循环阻力(或全肺阻力)
pulmonary circulation resistance
血液在肺部血管内流动时和血管壁之间的摩擦力和血液内部的摩擦阻力。肺动脉管壁较薄，分支短而管径大，故肺动脉的可扩性较大，对血流的阻力很小，仅0.12PRU(外周阻力单位)。肺循环动脉部分总的阻力和静脉部分总的阻力相等，故血液流动时在动脉部分的压力降落和静脉部分的压力降落相等。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条