1) velocity/sliding velocity
速度/滑动速度
2) sliding velocity
滑动速度
1.
The effects of load and sliding velocity on wear rate of ZTM are researched.
研究了载荷、滑动速度对ＺＴＭ磨损率的影响，并与ＴＺＰ、莫来石和氧化铝陶瓷的耐磨性进行了比较，对ＺＴＭ的磨粒磨损机理进行了初步探讨。
2.
In order to investigate the fractal behavior of friction signal and the change regularity of its fractal dimension with sliding velocity and contact load,friction and wear tests of pin(GCr15 steel)-on-disc(C45 steel) were carried out on an MMW-1 type wear tester.
在立式万能摩擦磨损试验机上对GCr15/45#钢摩擦副进行不同接触载荷和滑动速度下的摩擦磨损试验,对初始滑动距离1000 m内的摩擦系数信号进行数据采集,运用结构函数测度方法对摩擦系数信号进行分形表征,计算不同载荷和速度下的分形维数,研究摩擦信号的分形维数随载荷和速度的变化规律。
3.
So it′s important to research the mechanism of high-speed landslides,sliding velocity and time to predict the damages.
针对高速滑坡能量大、速度快,往往会带来灾难性破坏的严峻现实,研究滑坡的发生机制、分析滑坡体的滑动时间及滑动速度对预测滑坡体的破坏特征具有重要意义。
3) sliding speed
滑动速度
1.
Effects of Sliding Speed on Dry Sliding Wear Properties of Al_2O_3-SiO_(2(sf))/AZ91D Composites
滑动速度对Al_2O_3-SiO_(2(sf))/AZ91D复合材料磨损性能的影响
2.
Tests were carried out on a block-on-disk type high speed friction tester, and several sliding speeds of 20 m/s to 60 m/s as well as several normal pressures of 0.
实验在盘–块式高速摩擦试验机上进行,滑动速度为20～60m/s,法向压强为0。
3.
With the example of Dashiban Landslide in Three Gorges reservoir,this paper presents the empirical formula and slice analysis technique of kinemati,the two methods of surge calculation,that are used to preview the sliding speed,maximal initial surge height and capacity entering the river in different work conditions.
以三峡库区大石板滑坡为例,运用经验公式法和条块运动学分析法两种涌浪计算方法,预测滑坡不同工况下的滑动速度、初始涌浪最大浪高及滑坡入江体积,结果表明该滑坡最大入江体积为420。
4) slip acceleration
滑动加速度
5) relative sliding linear velocity
相对滑动线速度
1.
The effects of load and relative sliding linear velocity on the tribological behavior of the composites were investigated on a pin-on-disc test rig.
用热压成型法制备了超高分子量聚乙烯(UHMWPE)纳/米ZnO复合材料,采用销盘式摩擦磨损试验机考察了载荷和相对滑动线速度对复合材料摩擦学性能的影响;采用扫描电子显微镜观察了复合材料磨损表面形貌。
6) slowdown of slippage limit
滑动极限减速度
补充资料：缝纫速度
缝纫速度 sewing speed
缝纫机每分钟针刺的次数，单位为：针／min.
最高缝纫速度：缝纫机在正常缝纫条件下，能承受的最高针刺次数。
工作缝纫速度：缝纫机在正常缝纫条件下，能承受持续安全操作的最高缝纫速度。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条