说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 盲区补偿
1)  blind spot peneley
盲区补偿
2)  blind pixels compensation
盲元补偿
3)  CFO blind compensation
载波频偏盲补偿
1.
The synchronization is accomplished sequentially by CFO blind compensation,coarse time synchronization,CFO estimation,CFO compensation and symbol-timing synchronization.
给出了基于载波频偏盲补偿的MIMO OFDM系统同步算法:首先,将接收到的序列进行载波频偏盲补偿;然后,进行粗时间同步和载波频偏估计;最后,应用估计出的载波频偏进行载波频偏补偿,利用经过载波频偏补偿后的序列进行符号定时同步。
4)  blind pixel calibration
盲元定位与补偿
1.
The algorithm includes: noise distribution parameters estimation, blind pixel calibration, image de-noising, image segmentation and target extraction.
在深入分析空间观测图像中,像素灰度在空间和帧间分布特征的基础上,提出一种基于目标提取的空间观测图像预处理算法,算法包括:噪声分布参数估计、盲元定位与补偿、图像降噪、图像分割以及目标提取等步骤。
5)  Dead-Time Compensation
死区补偿
1.
Simulation of the dead-time compensation in vector-controlled induction motor;
异步电机矢量控制中死区补偿的仿真研究
2.
But the magnitude of output voltage will be affected and it’s waveform will be distorted by the existence of dead-time in its main circuitry without dead-time compensation.
单周控制静止同步补偿器是一种十分有效的无功补偿新方法,但由于其主电路功率器件存在固有死区,若不进行死区补偿,将严重影响装置的输出电压,使其波形失真,谐波含量加大。
3.
The dead time effects on the output voltage of the PWM voltage source inverter and a classification on dead-time compensations are presented.
详细地分析了脉宽调制(PWM)逆变器死区效应的发生机理及其影响,并对死区补偿方法进行了分类介绍,概括性地分析总结了各自的优缺点。
6)  dead time compensation
死区补偿
1.
The design method and implementation technology of the proposed digital controllers were recommended, which comprised the harmonic detecting method with high accuracy, control arithmetic of variable structure, dead time compensation and hardware implementation.
该数字化控制器的设计及实现技术包括:利用高精度的谐波检测技术从电网电流中瞬时检测出电网所包含的谐波分量,并将其作为参考电流信号;采用三重滑模变结构控制算法使有源逆变器的输出电流快速、准确地跟踪参考电流信号;实现死区补偿技术和数字化控制器的硬件电路。
2.
Finally, a dead time compensation method based on control chip MR16 was implemented.
最后,在对死区补偿原理分析的基础上,提出了一种基于MR16的软件死区补偿方法。
3.
The survey has been made on three sub areas,they are PWM basic technique,PWM technique combined with current control,and PWM dead time compensation technique.
针对交流伺服应用 ,文中分三个方面阐述了 PWM技术的近期发展 :PWM技术、与电流控制相结合的 PWM技术和 PWM死区补偿技术。
补充资料:《矿产资源补偿费征收管理规定》


《矿产资源补偿费征收管理规定》
provision on the administration of the collection of the mineral resouces compensation

  kuangehan ziyuan buehangfei zhengshou guanli guiding《矿产资源补偿费征收管理规定》(provision。。theadnlinistration of lhe eolleetion of the而nelal resoucesCon〕pensation)国务院1 994年2月27日发布,同年4月1日起施行。共22条,另附费率表。主要内容包括:①矿产资介 《矿产资源补偿费征收管理规定》 (《人民日报》 1994年3月6日)源属国家所有,开采矿产资源必须按照本规定向国家缴纳矿产资源补偿费。②矿产资源补偿费由地质矿产主管部门会同财政主管部门征收,地质矿产主管部门负责具体征收工作,财政主管部门负责征收的监督工作。③矿产资源补偿费按照矿产品销售收人的一定比例计征。④采矿权人应按照规定的义务、纳费期限、结算方式和纳费对象及其费率标准缴纳矿产资源补偿费。⑤征收的矿产资源补偿费应及时、全额、就地上缴中央金库,年终按规定的比例中央与地方分成,单独结算并纳人国家预算实行专项管理,主要用于矿产资源勘查。⑥免缴或减缴矿产资源补偿费,必须报经省级人民政府地质矿产主管部门会同同级财政主管部门批准。⑦采矿权人采取伪报矿种、隐匿产量、销售数量或伪报销售价格、实际开采回采率等手段,不缴或少缴矿产资源补偿费的,将处以加征滞纳金、罚款的处罚,情节严重的,吊销其采矿许可证。(殷德仁)
  
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条