1) normal pressure infiltration
常压浸渗
1.
In this paper,normal pressure infiltration of pure magnesium into B_4C particlebase plate with different compactibilities was studied,and the influence factors on thenormal pressure infiItration are discussed.
本文研究了纯镁对不同致密度的碳化硼（Ｂ＿４Ｃ）颗粒基片的常压浸渗性；讨论了镁液对Ｂ＿４Ｃ颗粒聚集体常压浸渗的影响因素；提出了浸渗模型。
2) gas pressure infiltration
气压浸渗
1.
Al/SiCP electronic packaging materials embedded metal components were fabricated by gas pressure infiltration.
采用气压浸渗技术完成了Al/SiCP电子封装材料嵌入金属元件的制备,应用能谱分析、XRD观察了界面层微观组织,并对界面连接强度进行了抗弯强度性能测试。
3) moulding pressure infiltration
模压浸渗
1.
Production technology of ZrW_2O_8/Al6013 composites prepared by moulding pressure infiltration method was introduced and the microstructure and coefficients of thermal expansion of ZrW_2O_8/Al6013 composites were studied.
介绍了模压浸渗复合法制备ZrW2O8/A l6013复合材料的工艺过程,并对该复合材料的组织和热膨胀性能进行了初步探讨。
4) pressure infiltration
压力浸渗
1.
The superplastic characteristics of the betaSiC whisker reinforced LY12 aluminum composite, fabricated by pressure infiltration and hotrolling after extrusion with a low extrusion ratio, were investigated The results show that the SiCw/LY12 composite exhibit a total elongation of 200%370% in the initial strain rate region from 33103 to 33102 s1at 788808
对压力浸渗、小挤压比挤压以及进一步轧制制备的β－ＳｉＣ晶须增强ＬＹ１２铝基复合材料的超塑性变形行为进行了研究。
2.
The scientific and technical matters concerned with the stability and the rheology properties of SiC slips, the packing behaviors of SiC powders, the manufacture of SiC tape and bulk skeletons, and the process of pressure infiltration were investigated.
研究了ＳｉＣ料浆的稳定性和流变特性、ＳｉＣ粉末的填实过程、ＳｉＣ薄带和骨架的制备技术、ＳｉＣ的固相烧结和骨架密度的控制，以及压力浸渗等科学问题和工艺问题。
3.
The article discussed the effect of preparing particle reinforced metal matrix composites by the path of pressure infiltration and the way of "nonuniform reinforced" to reduce the critical osmotic pressure and deformation degree of prefabricated body; and the possibility of improve plasticity and toughness of complex material to certain degree was also discussed.
本文通过“非均匀增强”的方式，探讨了用压力浸渗法制备颗粒增强金属基复合材料的途径，对减小临界浸渗压力及降低预制体变形程度的效果，以及在一定程度上改善复合材料塑性和韧性的可能性。
5) infiltration pressure
浸渗压
6) low pressure infiltration
低压浸渗
补充资料：常压浸出
常压浸出
atmospheric leaching
ehangya Jinehu常压浸出(atmospherie leaehing)在大气压下作业的浸出方法。在有色金属提取冶金中，常压浸出的应用较加压浸出更为广泛。金银矿石氰化物浸出(见氛化法提全)、氧化铜矿石堆浸(见铜矿浸出)、湿法炼锌中的锌焙砂的酸浸出(见锌焙砂浸出)、硫化锑精矿的硫化碱浸出(见碱性湿法炼锑)或羲盐浸出(见酸性湿法炼锑)、钨精矿的盐酸分解以及独居石精矿的氢氧化钠溶液分解(见稀土精矿碱法分解)等均系常压浸出的工业应用实例。此外，在诸如阳极泥、高镍梳等冶金中间产物的湿法冶金处理中，也大都采用常压浸出。与加压浸出相比，常压浸出的优点是设备简单、操作容易、作业成本比较低;缺点是某些难浸出物料的作业周期比较长。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条