|
|
1) UV form of ship stern
尾剖面UV度
2) after perpendicular section
尾垂线剖面
3) profile density
剖面密度
1.
Timber of Yunnan pine from plantation was treated with hot pressing,water boiling and steaming,the profile density of treated timber was determined.
采用热压、水煮和汽蒸对云南松人工林的云南松材进行了处理,对经处理的云南松材剖面密度进行了测定。
4) density profile
密度剖面
1.
Because the advanced technique such as computer sampling system is applied, it can continuously and quantutively measure the conductivity and initial density profile of the stratified flow, and oscillation of isopycnal generated by internal waves, and save these data into computer disk.
本文描述作者研制成的一种专用于实验室水槽密度层化食盐溶液中内波实验的仪器，该仪器采用微型计算机等先进技术，能够连续定量采集层化盐水电导率和密度剖面以及内波产生的等密度面起伏的时序数据，使内波实验由定性提高到定量水平，仪器具有探头体积小、精度高、测量范围宽、采集和控制自动化程度好等优点，是内波实验研究的有效手段。
5) concentration profile
浓度剖面
6) velocity profile
速度剖面
1.
The authors applies seismic high resolution nonlinear inversion method to the seismic data of Ebei region with narrow wave band, low master frequency and message-to-noise ratio to obtain high quality and high resolution seismic inversion profile (velocity profile).
将地震高分辨率非线性反演方法应用于地震频带窄、主频低和信噪比低的鄂尔多斯盆地鄂北区块地震剖面的反演,获得了品质高和分辨率高的地震反演剖面(速度剖面)。
2.
Under the different pressure gradients for liquid and gas flow,the variation of the velocity profile in the model and the thickness of the shear layer were investigated.
用线性稳定性理论研究了内部为轴对称液体射流、外部为同轴气体射流的粘性双流体模型· 在液体射流和气体射流分别处于不同压力梯度作用的条件下,讨论了数学模型中射流速度剖面形状变化,并用Chebyshev配点法研究了剪切层厚度变化及其对界面稳定性产生的影响·
3.
Objective To study the asymmetry of velocity profile under steady flow condition in the curved common carotid artery(CCA) in vitro.
目的模拟研究弯曲颈总动脉定常流动速度剖面的不对称性。
补充资料：关于solidworks 中的剖面线中的剖面线
solidworks的剖面线线型定义和autocad相同,它使用了autocad的剖面线定义方法,与autocad通用.因此,可以对剖面线进行定义. 方法:修改\SolidWorks\lang\chinese-simplified\sldwks.prn 用笔记本打开该文件,添加需要的线形.如 ;; Based on AutoCAD Ver.13.0s Hatch Pattern File ;;;; solidworks 区域剖面线定义文件 :: *金属, (Iron BrickStone), ANSI Iron, Brick, Stone masonry 45, 0,0, 0,.125 *塑料, (Lead Zinc Mg), ANSI Lead, Zinc, Magnesium, Sound/Heat/Elec Insulation 45, 0,0, 0,.125 135, 0,0, 0,.125 *玻璃,AR-GLASS@1.0 45,0,0,0,0.5, 0.5,-0.5 45,0,0.1414214, 0,0.5, 0.3,-0.7 45,0.1414214,0, 0,0.5, 0.3,-0.7 *软木, Cork material@1.0 0, 0,0, 0,.125 135, .0625,-.0625, 0,.35355339, .176776696,-.176776696 135, .09375,-.0625, 0,.35355339, .176776696,-.176776696 135, .125,-.0625, 0,.35355339, .176776696,-.176776696 *无, None 删除不需要的定义类型,可以大大提高solidworks 的启动速度
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条
|