说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 接地方位
1)  ground touching position
接地方位
2)  Azimuth mosaic
方位拼接
3)  earthing position
接地位置
4)  earthing mode
接地方式
1.
How to choose the neutral earthing mode of main power transformer in 110kV power network;
110kV电网如何选取主变中性点接地方式
2.
Neutral point earthing mode of generator in a project was analysed and neutral point earthing transformer characteristics were calculated.
通过对非洲某国电站发电机的中性点接地方式进行分析,对发电机中性点接地变压器的选型进行了工程计算,指出发电机中性点接地变压器的参数选择须与发电机定子接地保护相配合。
3.
In accordance with three types of blade earthing modes for disconnector with earthing switch blades of overhead contact line in subway, by comparison based on the system principles, it obtains the conclusion that the mode connecting from rail to negative pole is rather reasonable, and proposes to adopt the mode connecting the earthing blades to the rail during construction.
针对地铁架空接触网带接地刀闸隔离开关的3种刀闸接地方式,从系统原理进行对比分析,认为通过钢轨至负极的方式比较合理,建议工程中采用接地刀闸接至钢轨方式。
5)  grounding method
接地方式
1.
Anti-interference analysis for the grounding methods of control cable shielding line;
控制电缆屏蔽层接地方式的抗干扰分析
2.
Study of neutral grounding method based on manual earthing & dividing current technique for small current earthing systems;
基于人为接地分流的小电流接地系统中性点接地方式研究
3.
Discussion on application of arc-suppression coil grounding method in 10 kV distribution network systems;
10kV配网系统消弧线圈接地方式应用探讨
6)  grounding mode
接地方式
1.
Analysis on grounding mode of transformer neutral-point;
变压器中性点接地方式分析
2.
Neutral grounding modes for 10 kV system;
10kV系统中性点接地方式
3.
This paper introduces the grounding system and various grounding modes, and puts forward the grounding system, electric protection methods and grounding measures that the modern intellectualized buildings should adopt.
在介绍接地系统和各类接地方式的基础上,提出了现代智能化建筑应采取的接地系统、电气保护方式与接地措施。
补充资料:电力系统中性点接地变压器接地


电力系统中性点接地变压器接地
earthing transformer for neutral grounding

d旧n]一x .tong之hongx旧gd一onj旧d一b旧nyoq一j旧d-电力系统中性点接地变压器接地(earthingtransformer for neutral grounding)电力系统中利用接地变压器获得中性点与大地连接,也称中性点辅助变压器接地。当系统中的变压器不具备接人电阻器或接地故障消除器的条件(例如变压器三相绕组为△接线或虽为Y接线但容量不符合要求)时,要利用辅助的变压器提供一个用于接地的中性点。这种变压器应具备零序阻抗低、激磁阻抗大、功率损耗小的特性。绕组为曲折(Z)接线的变压器符合要求,如图1(a)所示。它可以带二次侧绕组,也可以只有一次侧绕组。 这种变压器每相由匝数相等的两个串联分绕组组成,每个磁芯上的两个分绕组间以及它们对二次侧绕组的零序互磁为零。很明显,这种变压器的零序电抗XTo只为变压器一次侧绕组的漏电抗Xs,,即XTo-Xs;,而系统中性点与地之间的计算阻抗Z。为Z。一25,+Z。,其中Z。为中性点电阻器或电抗器的阻抗。见图1(b)。2.为激磁阻抗。见图2,YN,d接线的变压器二次侧绕组可以带一定负荷。从过负荷能力考虑已经知道.接YN,d接线的双绕组变压器中性点的接地设备的容t不应超过变压器额定容t的50%.由此可认为,当变压器额定容t按中性点接地设备的容t设计时,允许二次侧绕组带50%额定容t的负荷. 还有一种特殊接线的接地变压器和接地设备的组合,是1918年鲍赫(R.Bauch)发明的,故也称饱鹅变压器,见图3。变压器一次侧中性点直接接地,开口三角形接线的二次侧连接接地设备,这与一次侧中性点接有接地设备是等效的。单相接地时,不对称的电压可分解为对称的正序和零序,磁通也可分解为对应的分量。磁通人m、人。、人.需要极小的激磁电流,并对应于正序电压U.。、U、。、U。。,零序电压UO.对各相是一样的,故三个磁柱中有相同的磁通式,对零序磁通来说,变压器相当一个单相变压器,只不过分裂为3个磁柱和3个绕组,见图3(c)。单相接地时,这种变压器每个分绕组上的电压为少尹z‘一.哟.!|||一下咖l!补丰气l一!{屯犷!{屯享!孟=zl息)一刃川l|拍--l--﹄·图1绕组为曲折(Z)接线的变压器 (a)接线图.(b)零序阻抗图会‘价“相“压,·““”的““是中”点接地“备电流的1/3,即夸。因而变压器的额定功率为3x2‘会‘争即中性点接地设备“率”1.15倍。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条