1) absolute error bound
绝对误差界
2) global absolute error bound
全局绝对误差界
1.
In this paper,the estimation of the error bound for the generalized linear complementarity problem over a closed polyhedral cone(GLCP) was consider,and GLCP was equivalently converted into an affine variational inequalities problem over a closed polyhedral cone(AVIP) under suitable conditions,and then a global absolute error bound for GLCP establish as well.
在适当条件下将凸多面锥上的广义线性互补问题等价地转化为凸多面锥上的变分不等式问题,利用变分不等式的误差界,建立了凸多面锥上的广义线性互补问题的全局绝对误差界。
3) absolute error
绝对误差
1.
By comparison with the results of ideal Henon sequence mixed with noise,the improved Farmer algorithm is able to increase the precision of noise attenuation and reduce the absolute error between itself and ideal Henon sequ.
通过对混有噪声的Henon序列进行仿真实验,仿真结果显示,改进后的Farm er算法能够提高噪声衰减的精度,降低与理想Henon序列的绝对误差。
2.
According to original laser measure error and error analysis transfer expressions,calculations about absolute errors and relative errors of the measuring deformation of wing were performed.
以激光器的原始测距误差为出发点,依据误差传递公式,分析了测量机翼变形量的绝对误差和相对误差,并给出了计算仿真结果和相应的图形。
3.
It may measure the frequency and phase of the signal which begin from 10 Hz to 20 kHz,absolute error isn′t more than 1°.
可以对10 Hz～2 0 k Hz频率范围的信号进行频率、相位等参数的精确测量,测相绝对误差不大于1°;采用数码管显示被测信号的频率、相位差。
4) absolute value error
绝对值误差
5) SAD
[英][sæd] [美][sæd]
绝对误差和
1.
The proposed fast selection algorithm for intra prediction uses sum of absolute difference(SAD) to filter out some less probable modes,reducing the complexity of intra prediction and improving the speed of the mode decision.
提出的帧内预测快速选择方法利用宏块的绝对误差和(SAD)来缩小预测模式的范围,减少帧内预测的计算量,从而提高模式判别的速度。
2.
2, a new method by improving the calculation procedure of SAD in macro block is proposed in order to reduce time consuming of motion estimation with minimal loss in video bitrates.
2源码中的UMHexagonS算法进行分析,改进宏块中绝对误差和计算步骤,在保证视频序列信噪比的前提下减少运动估计的耗时。
6) Sum of Absolute Different Differences(SADD)
绝对差分误差和
补充资料：绝对误差
分子式：
CAS号：
性质：通常简称为误差。是测量值与真值之差。用来表征测定结果的准确度。当不知道真值时，就不能确定测量值的误差，通常以国际上公认的量值(如标准原子量值)、国家标准物质的保证值或纯净物质的组分含量当作真值使用，以衡量某一分析方法和测量结果的准确度。
CAS号：
性质：通常简称为误差。是测量值与真值之差。用来表征测定结果的准确度。当不知道真值时，就不能确定测量值的误差，通常以国际上公认的量值(如标准原子量值)、国家标准物质的保证值或纯净物质的组分含量当作真值使用，以衡量某一分析方法和测量结果的准确度。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条