1) sensitivity/optical waveguide spectrophotometry
灵敏度/光导光度分析法
2) optical waveguide spectrophotometry
光导光度分析法
1.
A method of optical waveguide spectrophotometry for determination of trace vanadium in crude oil and diesel oil has been described.
用自制的光导吸收池，对光导光度分析法测定原油、柴油中痕量钒（Ｖ）进行了研究。
2.
The feasibility of the long light-path optical waveguide spectrophotometry is studied by experimental research, The relations between radius of curvature of the optical waveguide cell and sensitivity and that between the length of optical waveguide cell and absorbance, and the bending of working curve, the repeatability of testing result of the new analytical technigue is discussed.
对长光路光导光度分析法的吸收曲线，光导吸收池曲率半径与吸光度之间的关系，光导池长度与吸光度之间的关系，工作曲线的弯曲性，测量数据的重现性等问题进行了实验研究。
5) integrated photosensitivity
积分光电灵敏度
1.
The effect of changing Be doping concentration in GaAs layer on the integrated photosensitivity for negative-electron-affinity GaAs photocathodes is investigated.
研究了变掺杂浓度结构对GaAs负电子亲和势光电阴极积分光电灵敏度的影响。
6) sensitivity analysis
灵敏度分析法
1.
An evaluation method of the confidence level of cold-rolling force model is thus presented as follows,which combines inequality coefficient method with sensitivity analysis.
提出了适合轧制力仿真模型的可信度评估方法:不等式系数法与灵敏度分析法相结合的方法,即首先定义了仿真模型的TIC值,并用现场采集的轧制数据计算轧制力模型的TIC值,依据TIC值判断轧制力模型是否适合于当前的轧制条件,据此定性分析仿真模型的适用性;然后用灵敏度分析法定量分析仿真模型输入参数集对输出的敏感性,两种方法相辅相成,就能准确地验证轧制力模型的有效性。
2.
The method combines Monte Carlo Simulation with a sensitivity analysis.
将蒙特卡洛模拟法和灵敏度分析法相结合 ,以直流潮流为基础 ,建立了输电系统可用传输能力 (ATC)计算的概率模型。
3.
The following studies are done in this paper: calculation model of Available Transfer Capability (ATC) is bulided, sensitivity analysis is used to solve ATC quickly of determinate states, based on this Montle Carlo Simulati.
本文针对电网输电能力展开如下研究:建立电网可用输电能力(ATC)的计算模型,采用一阶灵敏度分析法快速计算确定系统状态的ATC,在此基础上,采用蒙特卡罗模拟法考虑不确定因素对ATC的影响,模拟系统的运行状态,求取ATC相关概率指标;寻找提高电网输电能力的措施,尤其是利用FACTS技术提高ATC,本文提出考虑常见FACTS装置的ATC计算模型,采用一阶灵敏度分析法求解含FACTS元件的ATC。
补充资料：比色分析法(见紫外—可见分光光度法)
比色分析法(见紫外—可见分光光度法)
比色分析法见萦外一可见分光光度法。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条