1) stiffness proportion
刚度配置
2) stiffness matching
刚度匹配
1.
But many difficult such as calculation of load distribution, crush stiffness matching of each stanchion, and so on exist.
但多支柱起落架各个支柱间的载荷分配计算、缓冲刚度匹配等问题,国内外尚无相应的设计规范与设计准则加以解决。
2.
So the research on the working behavior and the stiffness matching of the joint between two kinds of material box-girders will have important theoretic significance and reference value for practical application.
因此,对连接部位受力性能以及刚度匹配的研究具有重要的理论意义和实际工程应用的价值。
3) stiffness distribution
刚度分配
1.
The result demonstrated that stiffness distribution between boundary beam and grillage-shaped beam came into being influence to the internal force of grillage-shaped beam.
结果表明:边梁与井字梁间的刚度分配会对井字梁内力产生不可忽视的影响,导致井字梁的配筋量产生较大变化,边梁自身的扭矩也会产生较大变化,而边梁刚度的变化对自身的配筋量影响较小。
4) Position stiffness
位置刚度
1.
Load capacity,stiffness(current stiffness and position stiffness) are primary performance criterions of an active magnetic bearing (AMB) system.
分别利用磁轴承的线性化模型和非线性有限元法 (FEM)计算转子偏心时对磁力、电流刚度和位置刚度的影响,并通过算例进行了比较。
2.
The load capacity and stiffness (current stiffness and position stiffness) are the primary performance criterions of an active magnetic bearing (AMB) system and depend on the size and geometry of the AMB and the performance of the control system as well.
5A下的电磁力及其电流刚度与位置刚度,预测了径向磁轴承的承载力,给出了其磁场分布图,并与磁轴承的线性化模型参数进行了比较。
5) mounting stiffness
悬置刚度
1.
By comparing the simulation results under different main bearing load,the effect of the coupling flange,the mounting stiffness and the elasticity of shaft coupling on main bearing load were discussed.
通过比较不同模型主轴承载荷差异,探讨了连接法兰、悬置刚度和联轴节等安装条件对主轴承载荷计算的影响。
补充资料：JPZ型三向等刚度橡胶减震器
分子式：
CAS号：
性质：JPZ-type tridirective equal rigid rubber mounting 橡胶减震器的一种。具有x、y、z三个方向等刚度、等自震频率。按负荷大小可分为JPZ-1、JPZ-2两种型号。由中央金属芯柱、伞形金属罩及橡胶连接而成，模压法生产。可满足导弹控制仪等设备的隔震和抗冲击要求。
CAS号：
性质：JPZ-type tridirective equal rigid rubber mounting 橡胶减震器的一种。具有x、y、z三个方向等刚度、等自震频率。按负荷大小可分为JPZ-1、JPZ-2两种型号。由中央金属芯柱、伞形金属罩及橡胶连接而成，模压法生产。可满足导弹控制仪等设备的隔震和抗冲击要求。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条