1) secondary voids
二次空穴
1.
It is found that, with blunting to verticles while crack initiating, crack propagating in 16Co14Ni10Cr2Mo steel is an alternative process through coalescence of microvoids, including primary voids and secondary voids located on high-energy interfaces.
研究发现，该钢种裂纹钝化方式为角形钝化，裂纹的扩展是高能界面上空穴连接够有选择性的过程，与一次空穴和二次空穴的形成有关。
2) primary voids
一次空穴
1.
It is found that, with blunting to verticles while crack initiating, crack propagating in 16Co14Ni10Cr2Mo steel is an alternative process through coalescence of microvoids, including primary voids and secondary voids located on high-energy interfaces.
研究发现，该钢种裂纹钝化方式为角形钝化，裂纹的扩展是高能界面上空穴连接够有选择性的过程，与一次空穴和二次空穴的形成有关。
3) two-dimensional hole gas
二维空穴气
1.
The valence band structure of p-type heterostructure quantum well and two-dimensional hole gas are calculated by this method and the reduced finite difference calculation.
提出一种p型半导体量子阱中二维空穴气的有效计算方法。
2.
To visualize the relationship between the collector current and source-drain voltage in the SiGe/Si chare injection transistor (CHINT), the mathematical model of this device is set up by using the tunnel model of two-dimensional hole gas(2DHG)in SiGe/Si quantum well.
为了能直观地体现SiGe/Si电荷注入晶体管的收集极电流与漏源电压的关系,利用输入端SiGe/Si量子阱中二维空穴气的隧道模型,建立起此类器件的输入输出数学模型,并利用MATLAB软件对所建模型进行了模拟,结果显示在漏源电压约为1。
4) secondary air
二次空气
1.
Effects of Secondary Air on the Microwave Regeneration of Diesel Engine Exhaust Particulate Filter;
二次空气对柴油机排气颗粒过滤体微波再生过程的影响
2.
In order to reduce the emission of pollutants from motorcycles,various aftertreatment technologies such as secondary air,multi-staged air supply,electro-controlled air supply and fuel electric jet technology were used.
简述了为减少摩托车污染物排放而采用的二次空气、多级补气和电控补气、燃油电喷技术等摩托车排放后处理技术,进一步阐述了这些技术与催化剂结合在降低摩托车排放污染物上的应用,分析了各种技术的原理和应用现状,同时对其优势和缺点进行了比较,阐述了目前排放后处理技术中存在的问题,对今后的发展提出了建议。
3.
Based on numerical simulation, obtains the distributions of the dry-bulb temperature of primary air and the dry-bulb and wet-bulb temperatures of secondary air along the flow direction of primary air and secondary air, and the temperature variation of water falling film.
建立了数学模型,对叉流平板式间接蒸发冷却过程进行了数值模拟分析,得到了分别沿一、二次空气流动方向一次空气干球温度和二次空气干湿球温度的分布,以及水膜温度的变化情况。
5) double vacuum chamber
二次真空
1.
The double vacuum chamber technology has been u sed.
新真空室采用二次真空技术,在加速器中心平面真空度达到了8×10-6Pa。
6) Secondary-Air Injection
二次空气
1.
The Research of Combining the Secondary-Air Injection with the Oxidizing Catalytic Converter to Reduce Motorcycle Exhaust Emission;
应用二次空气结合催化转化器减轻摩托车发动机排放的试验研究
2.
HC and CO are main harmful emission in motor ,therefore the technology that spur an exothermic reaction of HC and CO through the oxidizing catalytic converter combining with the electronically controlled secondary-air injection system in order .
在摩托车中，由于HC及CO是主要的有害排放物，因此本文主要探讨通过氧化型催化转化器结合电控二次空气技术，来促使后氧化放热反应的进行，以降低摩托车有害排放。
补充资料：输出反馈(见线性二次型次优控制)
输出反馈(见线性二次型次优控制)
output feedback
3h日c卜口fon以以{输出反馈型次优控制。(output王eedbaek)见线性二次
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条