1) transitional regions
过渡地区
1.
Thermal properties and technical economic evaluation of the envelope structure of an energy saving house in transitional regions;
过渡地区节能住宅围护结构的热工性能及技术经济分析
2) transition region
过渡区
1.
A CO_2 arc welding seam detection algorithm based on transition region;
基于图像过渡区的CO_2气体保护焊焊缝识别算法
2.
Extraction and segmentation of image transition region based on morphology;
借助形态学实现图像过渡区提取与分割
3.
Extraction of transition region of image based on ramp width reduction;
基于宽度细化的图像过渡区提取
3) transitional region
过渡区
1.
The results showed that adding Sc to the alloy could cause the transformation of phase structure and the composition of the pre-separation phase in the transitional region of the quintary alloy.
6Al10Ti5五元锆基块体非晶态合金在非晶态-晶态过渡区中先析相的相结构及组织形态。
2.
Using this method, the DSMC program is developed to simulate flows in transitional region around a sphere double cone and Apollo capsule, and the aerodynamic and thermal characteristics around the supersonic and hypersonic vehicles is investigated.
在此基础上建立了一套DSMC数值模拟程序,对球双锥和Apollo飞船在过渡区域流动进行了数值模拟,并分析了其过渡区域超音速、高超音速的气动力、气动热等问题。
4) Transition region
过渡区域
1.
Due to the non balance of the transition region s common interests, there are some defects in its adjustment system itself.
过渡区域由于其共同利益的非均衡性而使协调机制本身存在较大缺陷 ,因此 ,在调整过渡区域经济协调方式时必须在遵循发展、互利和协商、自主和平等的原则基础上作好以下几方面的制度安排 :( 1)以市场为基础构建经济协作区 ;( 2 )充分发挥过渡区域优势 ,建立和完善发展极 ,形成纵横交错的产业带网络 ;( 3 )建立和完善过渡区域市场 ,推动过渡区域经济的发展 ;( 4 )建立新型的区际利益协调机制 ,充分发挥过渡区域经济运行协调机制的作用。
5) transition zone
过渡区域
1.
By testing and analyzing the interface of cladding plate(SA266-304) using by pressure vessel, it is found that there are still micro defects such as“seam”,“hole” and “transition zone” etc for the cladding plate which is up to the standard.
通过SA2 6 6 - 30 4压力容器用爆炸焊接复合板界面测试分析 ,发现符合国家标准的复合板由于界面仍存在“缝隙”、“空洞物”、“过渡区域”等几种微观缺陷 ,使得复合板在后续热处理、轧、校、卷以及使用过程中易出现开裂失效。
2.
The collision effects on the detonation transition zone were investigated.
采用二阶精度NND差分格式和改进的二阶段化学反应模型模拟了爆轰波与激波的对撞过程,研究了不同强度入射激波对爆轰过渡区域的影响。
6) transition zone
过渡区
1.
Then a hypothesis of “transition zone” on the interface between TiB2(TiC) and aluminum melt has been put forward for analysis.
15C形式加入微量TiB2或TiC的铝熔体,其粘度增加30%左右;分析了熔体粘度突变的原因,并提出了钛化物/铝熔体界面过渡区的假设。
2.
The cold-bend forming process was studied using energy method and a theoretical length expression of the transition zone of delormation was thus derived.
采用能量法原理对冷弯变形过程进行研究与分析，建立了变形过渡区长度的理论表达式。
3.
The results indicate that there is a special district in the transition zone,in which the materials have a high photosensitivity and a low crystalline volume fraction(Xc) with several tiny.
结果发现:在非晶/微晶过渡区内存在着一个光敏性较大的区域,这个区域内的材料晶化率为零,但是表面存在一些微小的晶粒;与拉曼散射光谱相比,X射线衍射光谱对微小的晶化更加敏感。
补充资料：太平洋地区标准会议标准(见太平洋地区标准会议)
太平洋地区标准会议标准(见太平洋地区标准会议)
standards of PASC: see Pacific Area Standards Congress; PASC
Ta iPingyang Diqu Bioozhun Hu呼ib沁幻Zhun太平洋地区标准会议标准(s切md田心sofR巧C)见太平洋地区标准会议。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条