1) rock yield strength
岩石屈服强度
1.
Fuzzy neural network is applied to deal with the test data on the basis of uniaxial compression test under the hydrostatic pressure, and the effect of hydrostatic pressure on rock yield strength is analyzed.
在静水压力作用下岩石单轴压缩试验基础上，应用模糊神经网络处理实验数据，分析了静水压力对岩石屈服强度的影响。
2) yield strength
屈服强度
1.
Effect of phosphorus on the yield strength of as-quenched GH761 alloy;
磷对GH761合金固溶水淬组织屈服强度的影响
2.
Study of influence factors of yield strength of oil and gas pipeline;
油气管道屈服强度影响因素的研究
3.
A modeling study of the yield strength of HRB335 hot rolled ribbed bar;
HRB335热轧带肋钢筋屈服强度模型研究
3) yield stress
屈服强度
1.
Based on the plain carbon steel with the chemical composition of 200MPa class steel the products of the yield stress of 400～500 MPa class and high-quality mechanical properties can be produced using the technology of chemistry tightly-tuning and controlled rolling - controlled cooling.
以屈服强度为 2 0 0MPa级的普碳钢为基本成分 ,采用成分微调与控轧控冷工艺相结合的技术路线 ,可将屈服强度提高到 4 0 0～ 5 0 0MPa,同时保证良好的综合性能。
2.
From the tests, a two-stage linear relation has been found between yield stress(σ_s) and strain rate(ε),σ_s=σ_0+klgε.
对４种金属材料进行了应变率为１０~（－４）—１０~３ｓ~（－１）的拉伸试验，结果表明，屈服强度随应变率的升高分两阶段线性升高。
4) yielding strength
屈服强度
1.
Yielding behavior of mismatched welded joint and prediction of its yielding strength;
非等强焊接接头屈服行为及屈服强度预测
2.
Mechanical properties of normalized and tempered 12Cr2Mo steel forgings,primarily yielding strength,were on the low side.
汽轮机用12Cr2Mo钢锻件经正火、回火后,其力学性能(主要是屈服强度)偏低,一次热处理后的合格率仅为50%,既造成该钢锻件大量热处理返修,又严重影响了生产周期。
5) yield point
屈服点,屈服强度
6) lower yield strength
下屈服强度
1.
The effect of tensile rate on the lower yield strength of the iron and steel material was investigated,the advantage of the tensile rate of GB/T228-2002 was discussed.
研究了拉伸速率对钢铁材料下屈服强度的影响,讨论了GB/T2 2 8-2 0 0 2中拉伸速率规定的科学性。
2.
Evaluation of uncertainty of measurement in testing for materials at ambient temperature has been discussed,including tensile strength;lower yield strength;proof strength,non-proportional extension;percentage elongation after fracture and percentage reduction of area.
文章介绍了金属材料室温拉伸试验测量结果不确定度的方法,内容包括抗拉强度、下屈服强度、规定非比例延伸强度、断后伸长率和断面收缩率等性能指标。
3.
According to GB/T228-2002 standard,"metallic materials tensile testing at ambient temperature",the lower yield strength of the cold rolled steel plate G450 has been tested.
根据GB/T 228-2002《金属材料室温拉伸试验方法》标准的要求,对牌号为G450冷轧钢板的下屈服强度进行了测试,并对其不确定度进行了评定。
补充资料：补偿屈服强度
分子式：
CAS号：
性质：应变超过应力-应变曲线成正比例的初始部分的指定量时的应力值。此指定的应变量称残余应变，也称偏置值。报告补偿屈服强度时一定要同时指明此偏置值。此值一般用于该材料没有明显的屈服点的场合。可以认为是一人为规定的屈服点，用于作条件性的相对比较。
CAS号：
性质：应变超过应力-应变曲线成正比例的初始部分的指定量时的应力值。此指定的应变量称残余应变，也称偏置值。报告补偿屈服强度时一定要同时指明此偏置值。此值一般用于该材料没有明显的屈服点的场合。可以认为是一人为规定的屈服点，用于作条件性的相对比较。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条