1) single point bearing
单点支撑
2) support point
支撑点
1.
Extreme points and support points of a family of analytic functions with complex coefficients;
一类复系数解析函数族的极值点与支撑点
2.
Extreme pionts and support points of a class of harmonic univalent functions;
一类单叶调和函数族的极值点与支撑点
3.
On the support points of the unit ball of Hp′;
关于H_p′空间单位球的支撑点
3) supporting joint
支撑节点
1.
This paper presents methods for detail handling of small -angle supporting joints.
上海中福城三期工程是一幢高层钢结构居民住宅楼,主体结构采用钢结构框架-支撑体系,本文就工程中出现小夹角支撑节点提出细部处理的方法。
4) three-point-supporting
三点支撑
1.
Non-interference method of three-point-supporting and mechanical lags controlled by computer is selected for leveling.
在大吨位车载光学仪器支撑调平结构中,用自动调平代替原来的人工调平,选用无干涉的三点支撑方案,用计算机控制的机械支腿进行调平。
5) supporting point
支撑点
1.
In this thesis Gelfer function was studied in many aspects,including its supporting point,extreme point,the subordinate relations and coefficients in the function family,its functional dependency as well as the mapping of supporting and extreme points,and the corresponding results were worked out.
本文研究了Gelfer函数族的支撑点、极值点、函数族中的从属关系和函数族中函数的系数,函数从属性以及支撑点和极值点的映照性质,得到相应结果。
2.
Tao Yuanming s tragic life lies on the break-down of life s supporting point.
陶渊明的人生悲剧在于其人生支撑点的失落。
6) strong point
支撑点
1.
This paper points out that it is necessary for channel to specialize and illustrates the four strong points of background on which channel specialization can be realized truly.
提出了电视传媒频道专业化势在必行,阐述了其赖以真正实现的背景依托的四个支撑点。
2.
This article is meant to prove the following conclusion:For a designated mdimen-sional distribution F and a n-dimensional distribution G,if F has at least m+2 strong points or G has at least n+2,there would exist random vectors X and Y, which are dependent and uncorre-lated,and make X-F and Y-G.
本文证明了如下结论:对给定的m维分布F和n维分布G,如果F至少有m+2个支撑点或G至少有n+2个支撑点,则存在不独立且不相关的随机向量X和Y,使X~F,Y~G。
3.
We must seek the best point of agreement and strong point to guarantee the overall start of the strategy.
“两环开放带动战略”是河北省经济发展的主体战略,要保证“两环开放带动”战略全面启动,必须寻 找实施“两环开放带动”战略的最佳契合点和支撑点。
补充资料:闭式单点、双点压力机
| |||||||
主要参数内容 | 国际先进 | 国内先进 | 国内一般 | 国内落后 | 评定方法及说明 | ||
(一)加工精度 | 参照GB10924-89、GB10933-89、JB5200-91 | ||||||
1、滑块下平面对工作台上平面的平行度(mm) | 30%精度储备 | 20%精度储备 | 达到规定值 | 大于规定值 | |||
0.02+0.10/100×滑块下平面的被测长度 | |||||||
2、滑块行程对工作台上平面的垂直度 | 30%精度储备 | 20%精度储备 | 达到规定值 | 大于规定值 | |||
0.05+0.02/100×滑块行程长度 | |||||||
(二)结构性能 | |||||||
1、离合器、制动器接通率,当滑块行程次数≤16次/分时为70%,≤25次/分时为60%,≤45次/分时为50% | 大于规定值10% | 大于规定值 | 达到规定值 | 达不到规定值 | |||
2、液压超负荷保险装置、微调装置、吨位指示器 | 全部具有 | 全部具有 | 部分具有 | 没有 | |||
(三)噪声dB(A) | |||||||
1、公称力≤400kN | ≤85 | ≤87 | ≤88 | >88 | |||
2、公称力>400kN | ≤87 | ≤88 | ≤90 | >90 | |||
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条