1) ceramic pour pulp casting machine
卫生瓷注浆机
2) Sanitary ware
卫生陶瓷
1.
Application of additive in the slurry of sanitary ware;
卫生陶瓷泥浆添加剂的应用研究
2.
The super-smooth glaze of sanitary ware was obtained by once-fired technique.
采用一次烧成工艺制备了卫生陶瓷用超平滑釉(Ra≤10。
3.
The present developing status and standards of sanitary ware industry are summarized in this paper.
归纳了当今卫生陶瓷工业的发展现状和水平 ,对窑炉产业提出了的新要求 ,分析了某一新型窑炉的特点 ,对发展我国陶瓷窑炉产业提出了建
3) sanitary pottery
卫生瓷
1.
Making use of perlite as main raw materials,low firing temperature sanitary pottery body has been developed through cross experiment design.
以低质珍珠岩为主要原料,通过正交设计,研制出低温烧成卫生瓷坯料配方,针对其坯体色深、白度低的情况,成功研制出La2O3基高强乳浊釉对其有效遮盖。
2.
The Xingtai soda,feldspar,and Part quartz were rePlaced by the local pottery stone,waste materials of the factory in Producing sanitary pottery.
利用本地瓷石和厂内废料代替河北邢台碱、长石和部分石英生产卫生瓷，可降低产品烧成温度，提高产品质量。
4) sanitary wares
卫生陶瓷
1.
The applications of Guangxi-Qidao clay in ceramic paste and glaze of sanitary wares are studied on the basis of the study about the clay’s raw material capability.
在对广西气刀土原料性能研究的基础上,进行了在卫生陶瓷坯料、釉料中的应用研究。
2.
Through the adjust ion of Si/Al proportion and the doping of talc and matting agents,a calcium mat glaze for sanitary wares has been developed in this experiment.
本试验通过调整卫生陶瓷釉浆中的Si/Al,引入滑石和无光剂 ,成功地制备出卫生陶瓷钙质无光釉。
3.
The slip properties of the pressure casting on sanitary wares are studied,through a series of test,the influence of the slip properties of the slip casting process are discussed.
研究了卫生陶瓷压力注浆成型的泥浆性能 ,通过一系列试验 ,讨论了泥浆性能对压力注浆成型的影响。
5) sanitary products
卫生瓷
1.
Study on the key CAD technologies of sanitary products;
卫生瓷产品CAD系统关键技术的研究
2.
This paper sets forth the key technique and developing method of CAD for sanitary products .
阐述了卫生瓷产品CAD系统的开发方法及其采用的关键技术。
6) sanitary
[英]['sænətri] [美]['sænə'tɛrɪ]
卫生陶瓷
1.
The cross experimental research of Gel-casting technology on sanitary by using hydroxymethylacrylamide(HMAM)as monomerand ceric ammonium nitrate as initiator,N,N,N',N'-tetramethylethylenedimaine as catalyst,N,N'-methylenebisacrylamide(MBAM)as cross-linkeris conducted.
本文采用正交实验方法,以羟甲基丙烯酰胺为单体,硝酸铈铵为引发剂,N,N,N',N'-四甲基乙二胺为催化剂,N,N'-亚甲基双丙烯酰胺为交联剂,研究了卫生陶瓷凝胶注模成型工艺,并探讨了不同工艺条件(单体加入量、引发剂加入量、催化剂加入量、交联剂加入量等因素)对卫生陶瓷料浆凝胶注模成形后坯体的干燥速率、收缩率、干燥强度以及综合性能指标的影响规律。
2.
Gelcasting technology of sanitary using acrylamide as monomer and (NH 4) 2S 2O 8-NaHSO 3 as redox initiator was studied.
采用凝胶注模成型方法 ,以丙烯酰胺为单体 ,( NH4 ) 2 S2 O8-Na HSO3为引发剂 ,研究了卫生陶瓷凝胶注模成型工艺。
补充资料：瓷注
1.陶瓷茶壶。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条