1) Channelization
导流化
1.
Results show that the Channelization layout is advantageous over the roundabout layout,and that the traffic capacity could be significantly raised by setting up the walking subway or pedestrian overcrossing.
针对一“Ｙ”形交叉口的两种改造方案进行了分析和论证，计算表明：导流化方案优于环交方案；在经济许可的条件下设置人行地道或人行天桥将大大提高交叉口的通行能力。
2) diversion
导流
1.
The pipeline crossing plan of cofferdam, diversion and deep-wide excavation is chosen finally by comparing it with other river crossing plans such as underwater trench digging and directional control drilling.
兰成渝输油管道工程成渝段,管道沿线穿越的中小型河流都是U形断面河流,具有河岸与水面高差大、河两岸施工场地狭小等特点,通过对围堰导流大开挖穿越、水下成沟穿越、定向钻穿越等几种方案的分析,最终选定了围堰导流大开挖穿越方案。
2.
The construction diversion of the Tankeng Hydropower Station has the characteristics of big discharge and quick flow speed on its overflow cofferdam.
滩坑水电站施工导流过水围堰流量大,流速快。
3) river diversion
导流
1.
Design and construction methods on river diversion and river closure for the Laxiwa hydro project on the Yellow River, developed based on the hydrologic, climatic, topographic and geologic conditions, are described.
结合黄河上游拉西瓦水利枢纽工程的水文、气象、地形和地质等特点,论述了水利枢纽工程导流、截流设计及其施工方法。
2.
Through the research and the implementation of the navigation of the d iversion channel in TGP, and under the conditions of huge river diversion discha rge and extremely high navigation stream, the diversion channel satisfied the tr ansit capacity of passenger and goods and successfully solved the key technologi cal problems of the river diversion and the construction navigation.
通过三峡工程导流明渠导流通航研究及实践,在巨大导流流量和极高通航水流条件下,导流明渠满足了客货轮的通过能力,成功地解决了弯道上明渠导流及施工通航的关键技术问题。
4) flow-guided structure
导流结构
5) infinite flow
无限导流
1.
Based on solution to vertical crack model of infinite flow present by Gringartens and by classifying micro-sections for produced cracks and integrating with vertical crack model of uniform flow rate, half analytic solution to unstable flow pressure at bore bottom for 200 numbers of micro-sections of cracks is derived.
在Gringarten等人提出无限导流垂直裂缝模型解的基础上,通过对产生的裂缝进行微元段划分,结合均匀流率垂直裂缝模型,得出了裂缝微元段数为200时的井底不稳定流动压力的半解析解,根据杜哈美原理和二项式计算产能的方法,结合气井生产,提出拟合井底压力的方法,得到一种专门针对无限导流垂直裂缝模型的多产量测试产能预测模型。
6) baffle
导流板
1.
Design and simulation of baffle of fume hood;
通风橱导流板的设计与模拟
2.
The efficiency of twin-tangential annular flow gas distributor was determined by structures of baffles and sleeves.
双切向环流气体分布器性能的优劣与导流板和套筒结构的密切相关。
3.
Velocity distribution in oxidation ditch can be improved by installing front bsffle and back baffle based on researches and sumulation tests, so that sludge deposit in the bottom of oxidation ditch can be eliminated.
通过多年的研究和模拟试验 ,提出了加装前后导流板的措施以改善氧化沟的流速分布 ,消除目前氧化沟所存在的通病———池底积泥现象 ,而且很直观地给出了安装导流板前后的氧化沟各断面流速分布图。
参考词条
补充资料：公理化方法(见公理化和形式化)
公理化方法(见公理化和形式化)
axiomatical method
gongllbuafangfa公理化方法化和形式化。(axiomatieal method)见公理
说明：补充资料仅用于学习参考，请勿用于其它任何用途。