1) safety valve
泄爆阀
1.
Based on comparison and practice, necessity and reliability of us- age of new self-closing gas safety valves in gas purification systems are presented.
通过比较与实践,说明在煤气净化系统中,采用新型自闭式煤气泄爆阀的必要性和可靠性,并提出泄爆阀的设计技术参数。
2) Venting
泄爆
1.
Study on Quenching of Dust Explosion Venting;
粉尘爆炸泄爆火焰扑集研究
3) vented explosion
泄爆
1.
Numerical simulation of the vented explosion process of premixed gas in the communicating vessel;
连通器内预混气体泄爆过程的数值模拟
2.
Experimental investigations of external second-explosion induced by vented explosion;
泄爆诱导二次爆炸的实验研究
4) explosion venting
泄爆
1.
A methane-air mixture explosion venting process is numerically investigated in terms of Euler equations coupled with the element chemical reactions.
通过求解带化学反应的Euler方程,对甲烷-空气预混气体泄爆过程进行了数值模拟。
2.
These problems include high explosion venting rate of electrostatic precipitator, high equipment failure rate, poor performance of evaporative cooler nozzle, the production of high maintenance costs, large fluctuation of the dust contained in the flue gas and other issues.
针对莱钢120t转炉干法除尘系统使用实践中存在的电除尘器泄爆率高、设备故障率高、蒸发冷却器喷嘴性能差、生产维护成本高、烟气含尘量波动大等问题进行了系统分析,并采用防泄爆技术、蒸发冷却器喷嘴改进技术、系统整体切换技术、备件国产化技术等对系统进行优化改造,大大提高了系统运行安全,设备故障率为零,煤气含尘量稳定在8mg/m3以下,降低生产成本4元/t,年直接经济效益达1700万元。
3.
The concept of explosion venting encompasses all measures used to open the originally closed vessels and equipment either briefly or permanently in a non-hazardous direction following an explosion and explosion venting technology describes one of the possible protective measures against the effect of explosions.
泄爆是指通过泄爆装置将腔室或容器内已燃高压混合气体导入到外部环境中,使内部压力迅速降低以防爆炸的技术。
5) venting explosions
泄爆
1.
Pressure measurement inside and outside the vessel during venting explosions;
泄爆过程内外流场的压力测量
6) draining duct
泄爆烟管
1.
By analyzing the experiment of the draining duct,this paper puts forward the opinion that the draining duct can be added to the guide place of finished detonator,which can promptly drain off the wave produced by the explosion of detonator and greatly enhance the safe production.
本文通过对泄爆烟管进行实验分析,提出在原成品导通工位增设泄爆烟管的思路,在杜绝电雷管发生爆炸时能及时将爆轰波排泄出去,减少伤亡的问题上取得了良好的效果。
参考词条
补充资料:溢流阀、顺序阀、减压阀的比较
溢流阀 | 减压阀 | 顺序阀 | ||
控制油路的特点 | 通过调整弹簧的压力控制进油路的压力,保证进口压力恒定,p2=0 | 通过调整弹簧的压力控制出油口的压力,保证出口压力p2稳定 | 直控式-通过调定调压弹簧的压力控制进油路压力;夜控式-由单独油路控制压力 | |
出油口情况 | 出油口与油箱相连 | 出油口与减压回路相连 | 出油口与工作回路相连 | |
泄漏形式 | 内泄式 | 外泄式 | 内泄式 | |
进油口状态及压力值 | 常态 | 常闭(原始状态) | 常开(原始状态) | 常闭(原始状态) |
工作状态 | 进出油口相通,进油口压力为调整压力 | 进油口压力低于出油口压力,出油口压力稳定在调定值上 | 进出油口相通,进油口压力允许继续升高 | |
联接方式 | 并联 | 串联 | 实现顺序动作式串联作卸荷阀用时并联 | |
功用 | 定压、溢流或安全作用限压、稳压、保压 | 减压、稳压 | 不控制系统的压力,只利用系统的压力变化控制油路的通断 | |
进油腔压力p1控制阀芯移动 | 出油腔压力p2控制阀芯移动 | 进油腔压力p1控制阀芯移动 | ||
说明:补充资料仅用于学习参考,请勿用于其它任何用途。