1) stability design
压柱
2) brittle failure of pressed post
压柱脆坏
1.
The expressions are obtained for the displacement of stopping point of pressed post with unstable failure, the elastic energy relief amount of press and the inertial force imposed on press with brittle failure of pressed post and the largest displacement of press.
对压柱弱化阶段的压机－压柱系统的能量变化关系作了分析，得到压柱失稳破裂终止点位移、压柱脆坏时压机释放的弹性能和受到的惯性力以及压机最大动位移等表达式。
3) bending-compression column
弯压柱
1.
Therefore,we obtained approximate elasticity solution of bending-compression column with different moduli,which was based on its gravity and a horizontal subjected force on top.
通过合理简化模型,将不同模量弹性理论中定义在主坐标系下的本构关系重新建立在普通坐标系下,进行拉压分区,从而推导了考虑自重且顶部有水平推力的不同模量弯压柱近似弹性力学解答,并由横截面上正应力为零判定了中性层的形状和位置。
4) eccentrically loaded column
偏压柱
1.
The deflection and deformation of slender column and eccentrically loaded column of ultro-high strength concrete filled steel tubes under loading were studied.
对钢管超高强混凝土长柱、偏压柱在荷载作用下的挠度及变形特点进行了研究。
2.
Necessarily, this paper is engaged to research the behavior of reinforced concrete eccentrically loaded column strengthened with CFRP.
本文完成了23根钢筋混凝土柱的试验研究，研究了粘贴碳纤维布偏压柱承载力和刚度的变化；分析了碳纤维布粘贴对柱延性、裂缝分布及破坏形态的影响；研究了在不同偏心距下碳纤维布的作用发挥程度；比较了不同粘贴方式和不同混凝土强度对加固效果的影响。
5) eccentric compression column
偏压柱
1.
Analysis of the bearing capacity of RC eccentric compression columns encased in angle steels and strengthened with CFRP;
外包角钢与碳纤维布复合加固钢筋混凝土偏压柱承载力计算分析
2.
Experimental research on RC eccentric compression column strengthened with the combination of CFRP and angle steel;
外包钢与碳纤维布复合加固钢筋混凝土偏压柱试验研究
6) cylindrical pressure cylinder
压柱油缸
1.
The conditions of the cylindrical pressure cylinder on D38 Schnabel car before and after the reform are described.
叙述了D38型钳夹车压柱油缸改造前后的状态及改造措施的实施过程,并提出了D38型钳夹车液压系统使用维护注意事项,为今后的类似设计和运用提供经验。
参考词条
补充资料：柱塞助压压气成型
分子式：
CAS号：
性质：一种柱塞助压成型方法。系用柱塞将夹持在框架上的经加热软化的塑料片材压入阴模内，柱塞下降到终点时，用压缩空气使塑料片材紧贴阴模壁而成型。
CAS号：
性质：一种柱塞助压成型方法。系用柱塞将夹持在框架上的经加热软化的塑料片材压入阴模内，柱塞下降到终点时，用压缩空气使塑料片材紧贴阴模壁而成型。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。