1) freezing temperature stress
冻结温度应力
2) freezing temperature
冻结温度
1.
Preliminary study on meso-damage propagation characteristics of rock under condition of freezing temperature;
冻结温度对岩石细观损伤扩展特性影响研究初探
2.
CT scanning test of meso-damage propagation of rock under different freezing temperature;
冻结温度影响下岩石细观损伤演化CT扫描
3.
Effect of different factors on the freezing temperature of shallow top soil
不同因素对浅表土冻结温度的影响
3) frozen temperature
冻结温度
1.
Experimental analysis on the frozen temperature of typical soil of Bao-Lan railway frozen section;
包兰铁路冻害路段典型土的冻结温度实验分析
2.
The frozen temperatures of cow colostrum were measured under both the normal pressure and the low pressure.
以奶牛初乳为试验材料，测定了常压状态下与真空状态下的冻结温度，得出电阻变化率约１ＭΩ／ｍｉｎ作为共晶点温度选取依据。
3.
This text get the compression strength variety regulation of artificial frozen silty clay along with frozen temperature and moisture content by the compression strength experiment in different temperature and moisture content,and the result has some certain reference value to the design and construction of frozen engineering.
通过对不同温度、不同含水率下的人工冻结粉质黏土单轴无侧限抗压强度试验,得出其抗压强度随冻结温度和含水率的变化规律,试验结果对冻土工程的设计和施工具有一定的参考价值。
4) freezing point
冻结温度
1.
Using this installation, the unfrozen water contents of frozen soil under different pressures were determined, and the freezing point of soil corresponding to various pressures was calculated from the determined unfrozen water contents.
结合核磁共振仪，利用自行设计的机械加压装置，包括非金属材料制成的耐压试管，确定了冻土对应不同压力和温度的未冻水含量，并计算了相应压力下冻土的冻结温度。
2.
In order to study the effect of the soil freezing point on the calculation of frozen wall thickness,some models of the artificial ground freezing temperature field were established.
为了研究土层冻结温度对冻结壁厚度计算的影响,构建了考虑土层实际冻结温度的人工冻结温度场模型。
5) stress-freezing
应力冻结
1.
The application of stress-freezing technique to birefringent composite models is discussed.
通过对航空工业标准“复合材料薄板压缩试验方法”中推荐使用的试验夹具测试段应力场的光弹性验证试验，介绍了光弹性复合材料的应力冻结技术。
补充资料：冻结应力
分子式：
CAS号：
性质：亦称残余应力。在塑料成型加工过程中(如制有机玻璃板)，塑料制品在定型、冷却至成品时，仍有残留的、未消除的应力。其原因是聚合物的立体构型未达到平衡所致。透明的板材会出现银纹。
CAS号：
性质：亦称残余应力。在塑料成型加工过程中(如制有机玻璃板)，塑料制品在定型、冷却至成品时，仍有残留的、未消除的应力。其原因是聚合物的立体构型未达到平衡所致。透明的板材会出现银纹。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条