1) Fuel valve
燃油阀
2) fuel oil
燃油
1.
Study on the filter adhesive used to strengthen the automotive fuel oil filter paper;
汽车燃油滤清器滤纸增强用滤芯胶的研究
2.
Thermodynamic functions in the course of forming oleic acid/ammonia fuel oil alcohol water microemulsion system;
油酸/氨水-醇-燃油-水微乳体系形成过程热力学函数的研究
3.
Experimental Research on Combustion Characteristics of Magnetized Fuel Oil for Small Off Gun;
小油枪燃油磁化燃烧特性的试验研究
3) fuel
燃油
1.
Investigation on a fire accident in a fuel boiler room;
一起锅炉燃油火灾爆炸事故的调查
2.
Pollutional control of fuel systems for diesel locomotives;
内燃机车燃油系统的污染控制
3.
A Water Hammer Fuel Supercharging System of Gasoline Direct Injection;
一种用于缸内直接喷射的燃油水击增压系统
4) burning oil
燃油
1.
Measure method of burning oil pressure on electric control oil injection engine;
电控汽油喷射发动机燃油压力的测量方法
5) bio-oil
生物燃油
1.
The transportation of heat carrier is a key link of the procedure of bio-oil production.
热载体输送是生物燃油生产过程中的关键环节,输送过程的保温程度和输送效率直接影响生物燃油的生产。
2.
It's the key technology during the process of producing bio-oil to heat through heat-carrier,whether it's advanced or not is connected directly with the cost of bio-oil.
热载体加热是生物燃油生产过程中的关键环节,热载体技术先进与否直接关系到生物燃油的生产成本。
3.
This paper mainly introduced the theoretical basis,specified designing plan and the operating principle about the fuel-heating system of disel engine which use bio-oil/disel mixed fuel,founding solid base for the application of the bio-oil/disel mixed fuel on the common engine.
主要介绍了生物燃油/柴油混合燃料柴油机燃油加温系统设计的理论依据、具体的设计方案及其工作原理和过程,为生物燃油/柴油混合燃料能够在普通柴油机上推广应用奠定基础。
6) Fuel metering
燃油计量
1.
Study on fuel metering for the micro turbine engine;
微型涡喷发动机燃油计量技术研究
参考词条
补充资料:溢流阀、顺序阀、减压阀的比较
溢流阀 | 减压阀 | 顺序阀 | ||
控制油路的特点 | 通过调整弹簧的压力控制进油路的压力,保证进口压力恒定,p2=0 | 通过调整弹簧的压力控制出油口的压力,保证出口压力p2稳定 | 直控式-通过调定调压弹簧的压力控制进油路压力;夜控式-由单独油路控制压力 | |
出油口情况 | 出油口与油箱相连 | 出油口与减压回路相连 | 出油口与工作回路相连 | |
泄漏形式 | 内泄式 | 外泄式 | 内泄式 | |
进油口状态及压力值 | 常态 | 常闭(原始状态) | 常开(原始状态) | 常闭(原始状态) |
工作状态 | 进出油口相通,进油口压力为调整压力 | 进油口压力低于出油口压力,出油口压力稳定在调定值上 | 进出油口相通,进油口压力允许继续升高 | |
联接方式 | 并联 | 串联 | 实现顺序动作式串联作卸荷阀用时并联 | |
功用 | 定压、溢流或安全作用限压、稳压、保压 | 减压、稳压 | 不控制系统的压力,只利用系统的压力变化控制油路的通断 | |
进油腔压力p1控制阀芯移动 | 出油腔压力p2控制阀芯移动 | 进油腔压力p1控制阀芯移动 | ||
说明:补充资料仅用于学习参考,请勿用于其它任何用途。