1) outliers
例外点
1.
In this paper, the novel robust maximum entropy clustering algorithm RMEC, as the improved version of the maximum entropy algorithm MEC, is presented to overcome its drawbacks: very sensitive to outliers and uneasy to label them.
针对极大熵聚类算法MEC (maximumentropyclustering)对例外点 (outliers)较敏感和不能标识例外点的缺陷 ,提出了一种改进的极大熵聚类算法RMEC (robustmaximumentropyclustering)。
2.
In this paper a new robust fuzzy clustering neural networks (RFCNN) is presented to resolve the sensitivity of the fuzzy clustering neural network (FCNN) to outliers in real datasets.
针对模糊聚类神经网络FCNN(fuzzyclusteringneuralnetwork)对例外点(outliers)敏感的缺陷,通过引入Vapnik’sε-不敏感损失函数,重新构造网络的目标函数,并根据拉格朗日优化理论推导出新的鲁棒模糊聚类神经网络及其算法(robustfuzzyclusteringneuralnetworks,简称RFCNN)。
2) exception
[英][ɪk'sepʃn] [美][ɪk'sɛpʃən]
例外
1.
Rule-driven exception handling approach for Web Service composition;
一种规则驱动的Web服务组合例外处理方法
2.
Responsibility Ownership and Exception Which Delivery of the Goods without the Original B/L;
无单放货的责任归属及其例外
3.
The Research on the Influence of Limitations and Exceptions in the Copyright Law on the Long-Term Preservation of Digital Resources
著作权法中的限制与例外对数字资源长期保存的影响研究
3) exceptions
[英][ik'sepʃən] [美][ɪk'sɛpʃən]
例外
1.
An Exploration into the WTO s Exceptions of the Principle of National Treatment;
WTO国民待遇原则例外探析
2.
This paper focuses on exceptions to inheritance, particularly discusses its representation and reasoning facilities based on default logic, and proposes normal and semi-normal default rules for exceptions.
继承层次网络的非单调性表现为例外和矛盾2种情形。
3.
This paper has analyzed the essence and exceptions to this relativity principle, and those provisions which reflect and develop the principle in the Contract Law of China, and further given evaluations and suggestions, which are expected to be of help to modification and perfection of the Contract Law.
本文探讨了合同相对性原则的内涵及例外规定,并就我国《合同法》中体现合同相对性原则的制度以及在此基础上的例外规定作了分析和评价,并对完善《合同法》在这方面的规定提出了建议,期望《合同法》更富有人情味。
4) Exc. Except
除外,例外
5) floating-point divide exception
浮点除法例外;浮点除法异常
6) the Exception of Fraud Exception
欺诈例外的例外
补充资料:闭式单点、双点压力机
| |||||||
主要参数内容 | 国际先进 | 国内先进 | 国内一般 | 国内落后 | 评定方法及说明 | ||
(一)加工精度 | 参照GB10924-89、GB10933-89、JB5200-91 | ||||||
1、滑块下平面对工作台上平面的平行度(mm) | 30%精度储备 | 20%精度储备 | 达到规定值 | 大于规定值 | |||
0.02+0.10/100×滑块下平面的被测长度 | |||||||
2、滑块行程对工作台上平面的垂直度 | 30%精度储备 | 20%精度储备 | 达到规定值 | 大于规定值 | |||
0.05+0.02/100×滑块行程长度 | |||||||
(二)结构性能 | |||||||
1、离合器、制动器接通率,当滑块行程次数≤16次/分时为70%,≤25次/分时为60%,≤45次/分时为50% | 大于规定值10% | 大于规定值 | 达到规定值 | 达不到规定值 | |||
2、液压超负荷保险装置、微调装置、吨位指示器 | 全部具有 | 全部具有 | 部分具有 | 没有 | |||
(三)噪声dB(A) | |||||||
1、公称力≤400kN | ≤85 | ≤87 | ≤88 | >88 | |||
2、公称力>400kN | ≤87 | ≤88 | ≤90 | >90 |
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条