1)  oil quality
油质合格率
1.
Presents the new statistic method proposed for oil quality through analysis of the drawback of current statistic method for oil quality.
对现行的油质合格率统计方法的局限性进行了分析 ,提出了一种新的油质合格率统计方法 ,分析了它的科学性并介绍了试用情
2)  oil quality
油质
1.
The result of oil quality.
初步油质检验表明 ,水酶法比浸出法制得的毛油更清亮 ,酸价略低 ,磷脂少 ,油质稳定。
2.
It is believed from analysis that the main causes resulting in said troubles are due to long-term exceedng set standard for the quality of fire-resistant oil,The main causes leading oil quality to be not up to standard are as follows: local overtemperature,local standstill of oil flow,and insufficient regeneration etc.
沙角C电厂3×660 MW机组自投产以来高、中压汽阀(汽阀)故障频发,分析认为其主要为抗燃油品质长期超标所致,而油质不合格的主要原因为局部超温、局部油滞留、再生不足等。
3.
It analyze the mechnism and factor influencing turbine lubricating oil quality,and have got the conclusion of major oil quality pollution source being made by bearing box inversing pressure and sealing steam leaking,thus an oil fender functional improvement is put forward.
分析了影响汽轮机润滑油质的因素及机理 ,认为轴承箱内负压和汽封漏汽造成油挡处成为重要的油质污染点 ,建议对油挡进行结构改进 ,并提出改进方案和设
3)  crude oil characteristics difference
油质差异
4)  oleaginous grade
油质品位
1.
It is indicated from drilling that Chepaizi swell is characterized by multiple oil-bearing zones,multiple reservoir types and multiple oleaginous grades.
钻探表明,车排子凸起具有多含油层系、多油藏类型和多油质品位等“三多”成藏特征。
5)  gasoline quality
汽油质量
1.
It was showed that the technology can significantly reduce the olefin content of gasoline (20%-30% reduction), the gasoline quality to be improved, the octane number unchanged with gasoline test method, the octane number rose with motor test.
工业试验结果表明,该技术可以显著地降低汽油的烯烃含量(降低20~30个百分点),汽油研究法辛烷值不变,马达法辛烷值上升,汽油质量得到提高。
6)  crude quality
原油质量
参考词条
补充资料:不合格品率控制图(p图)


不合格品率控制图(p图)
control charts for fraction defective

  buhsgePinIO kongzhitu不合格品率控制图《p图)(cootrol chaztsfor俪ction de公兑tive)利用样本的一定类型的不合格品率(川,评估和监察过程的控制图,也是计数型控制图中最常用的控制图。计数数据往往能够快速而较便宜地取得,一般也不需要特别的收集技巧。计数型控制图的参数均值(产)与标准差(的是互相关的:例如,样本不合格品率(川的均值巧=p,标准差丐二石可下不下石,式中尸为过程或总体的平均不合格品率,。为样本大小。确定产,、凡中的一个就等于确定另一个,故只有一个独立的参数,即总体平均不合格品率p,因此,控制不合格品率(p)仅一张控制图就足够了。p图用于控制对象为不合格品率或合格品率等计件值的场合。常见的不良率有不合格品率、废品率、交货延迟率、缺勤率、差错率等。 p图的控制界限也是从休哈特控制图控制界限的总公式,即休哈特的3。方式导出的,具体如下:UCL二P+3_户,。丫六,一户,。CL二PoPLCL二P一3了P(l一P)/n了P(l一P)In。户一3丫户(:一户)/n式中:UCL为上控制限,比L为下控制线,CL为中心线,笋为总体平均不合格品率p的估计值,通常久。所有不合格品数厂“厂二一班看释魂礴「一 由于在p图的上下控制界限uCL、优L公式中含有样本大小n,故当n变化时,p图的上下控制界限呈凹凸状,不但作图难,而且更重要的是在p图上难于判断异常,也难于判断稳定。这时采用通用拉制图,可以克服上述困难。下页左图是一个实例的p图与不合格品数通用控制图(pn;图)的对比。(孙静)
  
说明:补充资料仅用于学习参考,请勿用于其它任何用途。