1) Point to point structure
点-点结构
2) Structure Characteristic
结构特点
1.
The structure characteristic and management of DZ type outside-pourable monomer hydraulic supports;
DZ型外注式单体液压支柱的结构特点及管理措施
2.
The assembly techniques and structure characteristic of the generator stator in Dachaoshan hydro-power station;
大朝山水电站发电机定子结构特点及装配工艺
3.
The structure characteristics and energy-saving effect of amorphous alloy transformer;
非晶合金铁芯配电变压器的结构特点和节电效果
4) laser light structure
点结构光
1.
Several light incisions are formed when the large size part is scanned along the cross-section by laser light structure sensors.
应用多个激光点结构光传感器对大尺寸工件横断面进行扫描,形成多个光切平面;拟合各个光切面上离散点为空间椭圆曲线,求出光切面中心的空间三维坐标,由此确定大尺寸工件轴线的直线度,并计算出横截面几何形状。
2.
Several light incisions are brought up when the large size parts are scanned along the cross-section by laser light structure sensors.
应用多只激光点结构光传感器对大型回转体工件横断面扫描,形成多个光切平面。
5) structure characteristics
结构特点
1.
Installation method and structure characteristics of turbine-generator units for Pengshui hydropower station
彭水水电站水轮发电机组结构特点和安装方法介绍
2.
The paper introduces the technical parameters,working principle,main structure characteristics of the rotary drum type differential speed cutting flying shear imported from Japan;and describes the shearing process and shearing quality.
介绍了从日本引进的异周速双滚筒切头飞剪的技术参数、工作原理、主要结构特点,对剪切过程及剪切质量进行了描述;应用力学原理,分析了剪切过程中滚筒组的扭转变形规律,相应的刀刃侧隙沿滚筒轴线变化特点,M-T齿轮对的功用,分配齿轮和M-T齿轮所具有的正变位、短齿、齿向修形结构特点。
3.
The preparation and structure characteristics of organosolv lignin were introduced in this article while its applications on polymer synthesis and modification were presented in detail.
溶剂型木质素(Organosolv lignin)与传统木质素盐类相比具有反应活性基团含量高、容易提纯以及不含任何含硫杂质等优势,论文着重介绍了溶剂型木质素的制备、结构特点以及近几年来在高分子合成和改性领域的研究进展,并对其发展方向作了总结。
6) structural characteristics
结构特点
1.
The development of 70 m~3 polymerizer and its structural characteristics;
70m~3 PVC聚合釜的研发与结构特点
2.
The structural characteristicsand the changing laws of knitted garment;
针织服装上衣结构特点及其变化规律研究
3.
Design capabilites and structural characteristics of generating units of the Three Gorges power station;
三峡机组设计性能及结构特点
补充资料：闭式单点、双点压力机
| |||||||
主要参数内容 | 国际先进 | 国内先进 | 国内一般 | 国内落后 | 评定方法及说明 | ||
（一）加工精度 | 参照GB10924-89、GB10933-89、JB5200-91 | ||||||
1、滑块下平面对工作台上平面的平行度（mm） | 30%精度储备 | 20%精度储备 | 达到规定值 | 大于规定值 | |||
0.02+0.10/100×滑块下平面的被测长度 | |||||||
2、滑块行程对工作台上平面的垂直度 | 30%精度储备 | 20%精度储备 | 达到规定值 | 大于规定值 | |||
0.05+0.02/100×滑块行程长度 | |||||||
（二）结构性能 | |||||||
1、离合器、制动器接通率，当滑块行程次数≤16次/分时为70%，≤25次/分时为60%，≤45次/分时为50% | 大于规定值10% | 大于规定值 | 达到规定值 | 达不到规定值 | |||
2、液压超负荷保险装置、微调装置、吨位指示器 | 全部具有 | 全部具有 | 部分具有 | 没有 | |||
（三）噪声dB（A） | |||||||
1、公称力≤400kN | ≤85 | ≤87 | ≤88 | ＞88 | |||
2、公称力＞400kN | ≤87 | ≤88 | ≤90 | ＞90 | |||
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条