1) assembly platform test method
台架试验方法
1.
Especially it brings forward that assembly platform test methods should be standardized and recommended evaluation specification should be detailed out during standard constitution, which may act as a reference in product development and performance improvements.
针对汽车电动助力转向总成性能试验,给出前期研究与实践的方法、理解要点,特别提出标准制定中应规范台架试验方法,细化推荐评价指标,以便为产品开发和性能改进提供对照。
2) Bench test
台架试验
1.
Load-feedback scheme comparison in bench test of AC traction drive system and traction motor;
交流牵引传动系统及牵引电机台架试验负载反馈方案的比选
2.
The results of bench test and service test for 3920 h in COSCO Guangzhou show that this oil has reliable quality and stability,and corresponding to the reference oils abroad.
台架试验和广州远洋运输公司3920h的使用试验表明:研制油品表现出可靠的使用性能和稳定性,总体性能与国外同类油品性能相当,可以满足90年代以后制造的低速二冲程十字头式船用发动机汽缸的润滑。
3.
Results of simulation evaluation and bench test showed that this oil has good detergent dispersing property,acid neutralization property and antiwear property,corresponding with the reference oil abroad.
经实验室各项模拟评定和台架试验结果表明 :油品具有较好的清净分散性、酸中和性和抗磨性 ,质量水平与国外参比油相当。
3) test bench
试验台架
1.
The evaluation test benchs of hydraulic fluid and score principle are presented systematically,including some pump test benchs such as Vickers 104C,Denison T5D,Denison P 46,Sundstrand 22,Vickers 35VQ25,Denison T6C,Vickers 20VQ5.
系统介绍了液压油评定试验台架。
2.
This paper deals with present test benchs at home and abroad about the evaluation test of anti-wear hydraulic oils,including four-ball wear tester,γ wear tester,vane/piston pump standard test benchs,radioactive trace technology wear tester.
对目前国内外液压油抗磨性能评测的试验设备和方法进行了分析探讨,包括四球试验机、伽玛磨损试验机、叶片泵/柱塞泵标准试验台架、放射性跟踪磨损试验机等试验系统。
3.
The test bench for engine thermal management system was built up by simulating the engine installation and application conditions like the water tank,the fan,the engine layout,the accessory and the pipe connection in the whole vehicle.
模拟发动机在整车中的安装使用条件,如水箱、风扇、发动机在机舱中的布置、附件及管路连接等,搭建发动机热管理系统试验台架。
4) rig test
台架试验
1.
This relation can be tested through rig test which is performed with standard PDC test bit.
复合片钻头的钻速与其切削齿的自锐性密切相关,钻头台架试验反映了这种内在联系,并用平均钻速((?))和平均钻速变化率((?))等指标对复合片自锐性能进行描述与评价。
2.
It is necessary to carry out reliability rig test of automatic load system prototype so as to deal with fault problems such as cartridge jamming and failure to feed in reliability rig test.
为使阻弹、卡弹等故障尽可能地解决在火炮自动装填系统可靠性台架试验中,有必要进行自动装填系统样机可靠性台架试验。
6) test platform
试验台架
1.
Test Platform of Anti-rolling Tank and Experimentation Research on Motion of Rolling and Swaying;
减摇水舱试验台架及横摇和横荡运动实验研究
2.
The test platform of ship anti-rolling tank is the important test facility of studying characteristics of the anti-rolling tank.
船舶减摇水舱试验台架是研究减摇水舱特性的重要试验设备,而能否准确地模拟船舶在海浪中的横摇运动是设计试验台架的关键。
3.
The oscillation tests were made,including different arrangement of vertical position, different water levels and different damping factors by the test platform.
利用我校研制的船舶减摇水舱试验台架进行了水舱不同垂直位置布置、不同边舱液位高度及不同的阻尼板开度的强迫振荡试验。
补充资料：PRO/E模架库安装方法
选择要安装的模架库，指明安装路径如D:\PTC,开始安装。
安装完后进入D:\PTC\moldlib\bin\i486_nt(或95)下，运行mkmoldconfig.exe,
敲上模架库路径D:\PTC,产生"config.pro"文件，这时就将这个文件里的内容
合并到您的"config.pro"文件里就行了，模架库就可挂上了。
再在您的"config.pro"文件里设置：search_path D:\PTC\moldlib\
search_path_file D:\PTC\moldlib\bin\i486_nt\config.pro
模架库就挂上了。
在您的"config.pro"文件里设置：menu_translation both就可以中英文并存了。
模架库启动方法：
启动PROE，新建Assembly里的Design,产生asm0001.prt文件，再打开上边Applications
下拉菜单
中的mold layout,右边菜单选第二项Mold Base,再选ADD,选择合适模架就行了
安装完后进入D:\PTC\moldlib\bin\i486_nt(或95)下，运行mkmoldconfig.exe,
敲上模架库路径D:\PTC,产生"config.pro"文件，这时就将这个文件里的内容
合并到您的"config.pro"文件里就行了，模架库就可挂上了。
再在您的"config.pro"文件里设置：search_path D:\PTC\moldlib\
search_path_file D:\PTC\moldlib\bin\i486_nt\config.pro
模架库就挂上了。
在您的"config.pro"文件里设置：menu_translation both就可以中英文并存了。
模架库启动方法：
启动PROE，新建Assembly里的Design,产生asm0001.prt文件，再打开上边Applications
下拉菜单
中的mold layout,右边菜单选第二项Mold Base,再选ADD,选择合适模架就行了
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条