1) offset
偏移线
1.
Considering the characteristic of polyline, we propose an algorithm to get the accurate offset of polyline.
计算平面曲线的偏移线在计算机辅助设计和数控加工中具有十分广泛的应用。
2) orbit-shift coil
轨道偏移线圈
3) Migration
偏移
1.
Globally optimized Fourier finite-difference migration in offset domain.;
炮检距域全局优化傅里叶有限差分偏移
2.
Ground penetrating radar data imaging via the 2D finite-diffrence migration method;
2D有限差分偏移技术在探地雷达信号成像中的应用
3.
Magneto-electrotelluric full frequency segment migration imaging technique and its application;
大地电磁全频段偏移成像技术及其应用
4) offset
偏移
1.
Application of the offset analysis in aluminum electrolysis control;
铝电解控制中偏移分析的应用
2.
From the point of view of the error compensation, the lateral offset error compensation of the sub-reflector is discussed and calculated by applying the best re-pointing technique.
建立40m口径天线结构的有限元分析模型,依据有限元分析结果,对副面和馈源偏离理想位置的偏移量和偏移误差进行分析与计算;从误差补偿角度,运用最佳指向技术对副面横偏误差进行补偿分析计算。
3.
Based on solved the non-liner equations with Monte-Carlo method,this paper have a analysis in the error of the phase shifts when it have some offset of the main beam in antenna pattern and have a group of results of the errors.
文中在运用蒙特卡罗方法求解非线性方程组的基础上,对天线的主波束在一定的偏移下各个移相器取值的误差进行了分析。
5) shift
偏移
1.
In this paper,developed are a method and correspondent software for calculating formation permeability from the center frequency shift and travel time delay in direct Stoneley wave.
利用多极子阵列声波测井资料提取直达斯通利波、计算斯通利波中心频率偏移和时间延迟来进行地层渗透率反演的方法已被研究了多年。
2.
[Objective]To demonstrate the shift of the spinal cord to the concave side of the spinal canal in adolescent patients with idiopathic thoracic scoliosis,to investigate possible cause of the shift of the spinal cord and to explore its clinical relevance.
[目的]揭示青少年胸椎特发性侧凸患者椎管内脊髓的偏移,明确其变化趋势,并探讨其可能的发生机制和临床意义。
3.
This paper deduces the shift of the eletron beam whichhas the effect on the electromagnetical force through the oscilloscope,the unifrom motion underthe electric pressure of the oscilloscope,and the further discussion of the formof the level scanning line.
本文通过对示波器中电子束受电场力作用产生偏移的推导 ,对示波器中锯齿波电压下电子的匀速运动 ,以及水平扫描线的形成作进一步的论
6) deviation
偏移
1.
The relationship of loop height difference with deviation of pre-splitting rolled piece during three-strand splitting bar rolling;
三切分棒材轧制活套高度差与预切分轧件偏移
2.
Cause and Countermeasures for girder deviation of curved girder bridge;
弯梁桥梁体偏移成因分析与处治
3.
Analysis on the foundation pit support pile top deviation accident;
基坑围护桩顶部偏移事故分析
参考词条
补充资料：创建偏移剖面
要创建偏移剖面，必须通过在“草绘器”中进行草绘以定义切口轮廓。然后，垂直于草绘平面投影此轮廓。单击 
或“视图”(View)>“视图管理器”(View Manager)。“视图管理器”(View Manager) 对话框打开。单击“剖截面”(Xsec)。单击“新建”(New)。出现一个缺省的剖面名称。按 ENTER 键。“剖截面创建”(XSEC CREATE) 菜单打开。单击“偏移”(Offset)>“一侧”(One Side) 或“双侧”(Both Sides)>“完成”(Done)。“选取”(SELECT) 对话框打开。选取草绘平面，并定义查看方向和草绘方向。进入“草绘器”。选取用于尺寸标注的参照图元。草绘剖面轮廓并单击 
退出“草绘器”。 在“视图管理器”(View Manager) 中，单击“显示”(Display)>“设置可见性”(Set Visible)。“可见性”(Visibility) 对话框打开。单击“显示剖面线”(Show X-Hatching) 查看剖面。单击 预览或单击 接受选取的选项。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。