1) oil collecting film
集油膜
1.
It shows that the oil collecting film is a multilayer film when a kind of N,N dialkylacylamide is solely used to form a film to compress oil slicks on water surface, and is a transforming film or a liquid condensed film when it is blended into a solution with suitable solvents.
表明当N,N-二烷基酰胺类物质单独成膜时获得的集油膜为多层膜 ,而当选用合适的溶剂与其配制成溶液以后 ,所成的集油膜则为转变膜或液态凝聚膜。
3) oil film
油膜
1.
Foundation Mechanisms and Influence Factors of Oil Film in Deformation Zone for Cold Rolling Aluminum Sheets;
铝材冷轧变形区油膜形成机理及影响因素
2.
The study about the mechanical effects of the liquid viscous transmission oil film;
液粘传动油膜力学效应的研究
3.
Influence of temperature field of oil film of new type of thrust bearing on its optimal parameters;
新型可逆式推力轴承油膜温度场对最优参数的影响
4) film
[英][fɪlm] [美][fɪlm]
油膜
1.
The oil film of sliding bearing was squeezed and sheared in the dynamic load conditions.
滑动轴承在动载工作条件下运行时,承载油膜受到轴承挤压和旋转剪切两种运动作用。
2.
With a certain type of diesel engines as the example,this paper calculated the pressure of film with FEM according to the orbit of shaft center,and analyzed the pressure change of film along with the revolving of crankshaft and the relative location of connecting rod.
将轴心轨迹和有限元法相结合,并以某柴油机为例,根据轴心轨迹计算得到的结果,对轴瓦的油膜进行了有限元计算,分析了轴瓦上相同点处油膜压力随曲轴的旋转,轴颈与连杆相对运动情况下的压力变化,为分析轴瓦的油膜压力提供了一种新的方法,理论计算与分析的结论为分析轴承或轴瓦发生穴蚀破坏提供理论依据。
3.
The basic characteristics of Flash were described, and the process of making animation about oscillatory squeeze film was described.
论述了F lash动画的基本特点,介绍了制作挤压油膜动画过程,同时给出了针对滑动轴承实际工况模拟的动载油膜动画。
5) supplied oil layer
供油油膜
1.
The results show that,two bumps of the supplied oil layer resulted in two bum.
结果表明:供油油膜的两突起导致相应的压力、部分油膜比例和润滑油膜分布中也出现两突起;供油油膜的两突起能够扩大压力区和充分供油区域,能够局部改善润滑效果,但是对中心膜厚和最小膜厚影响很小;供油油量主要影响润滑状态,而供油油膜的形状在不同程度上也会影响润滑状态。
6) oil layer
油层;油膜
补充资料：油膜轴承油
分子式：
分子量：
CAS号：
性质：为抗氧防锈型润滑油。具有良好的粘温性能、抗氧化性、防锈性及抗泡沫性等。目前最重要为21号油膜轴承油，适用于轧钢机的动压、静压、动静压油膜轴承，也可用于低速、重负荷大型机械的滑动轴承。以原油经过常减压蒸馏、丙烷脱沥青、深度溶剂精制、溶剂脱蜡及补充精制所得润滑组分，再加入抗氧、防锈、抗泡沫添加剂调制而成。
分子量：
CAS号：
性质：为抗氧防锈型润滑油。具有良好的粘温性能、抗氧化性、防锈性及抗泡沫性等。目前最重要为21号油膜轴承油，适用于轧钢机的动压、静压、动静压油膜轴承，也可用于低速、重负荷大型机械的滑动轴承。以原油经过常减压蒸馏、丙烷脱沥青、深度溶剂精制、溶剂脱蜡及补充精制所得润滑组分，再加入抗氧、防锈、抗泡沫添加剂调制而成。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条