1) curing shrinkage
固化收缩
1.
Through the optimization of processing conditions in SMC mold, the optimum pressure release time and the pressure in the second stage are determined , and molding runs are carried out at two-stage pressure, and the mold temperature is reduced as appropriate to reduce curing shrinkage and improve surface-quality in SMC molding.
可显著降低SMC制品的固化收缩率,提高其表观质量。
2.
Based on two kinds of silver powder with different morphology and three matrixes with different curing shrinkage, six electrical conductive adhesives were prepared.
选用三种不同固化收缩率的基体树脂和两种银粉,分别配制了六种导电胶。
3.
Based on two kinds of silver powder with different morphology and three matrixes with different curing shrinkage,six electrical conductive adhesives(ECA) were prepared.
采用2种不同形貌的银粉、3种不同固化收缩率的导电胶基体配制6种导电胶,研究等温固化过程中导电胶基体的固化收缩率以及银粉形貌对导电胶电阻率的影响,探讨导电胶的导电机理。
2) Polymerization shrinkage mass
固化收缩量
3) curing shrinkage internal stress
固化收缩应力
4) solidification contraction
固化收缩作用
5) solidification shrinkage
凝固收缩
1.
The effect of mechanical vibration on grain refinement and solidification shrinkage of aluminum was investigated in this paper.
研究了振动场对纯Al晶粒细化和凝固收缩的影响,并着重进行理论分析。
2.
The several theory problems that should be paid more attention to,including heat flow rate,solidification shrinkage,mould wall distortion,taper design and corner radius,are put forward and illuminated.
提出并论述了高速方坯连铸结晶器冶金中结晶器热流、钢的凝固收缩、结晶器变形、锥度设计和圆角半径等问题,重点讨论了拉速、碳含量及润滑剂对热流的影响,不同碳含量的钢凝固收缩和相变特征以及结晶器热变形规律,提出了不同钢种的凝固收缩和相变收缩的计算方法和结晶器锥度、圆角半径的设计思路。
6) solid contraction
固体收缩
补充资料：固化收缩
分子式：
CAS号：
性质：热固性树脂在缩聚过程中由线型到体型的变化过程。这时相对密度也随之增加，结果使制品尺寸缩减。这种固化收缩的大小随塑料品种而异，在一定程度上和固化体系及工艺条件有关。了解固化收缩情况是指导模具设计的必要数据，也可用以推断树脂质量和固化条件的优劣。
CAS号：
性质：热固性树脂在缩聚过程中由线型到体型的变化过程。这时相对密度也随之增加，结果使制品尺寸缩减。这种固化收缩的大小随塑料品种而异，在一定程度上和固化体系及工艺条件有关。了解固化收缩情况是指导模具设计的必要数据，也可用以推断树脂质量和固化条件的优劣。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条