1) Temperature of bridge wire
桥丝温度
2) spinning temperature
纺丝温度
1.
Study on dynamic viscoelasticity of anti-dripping and flame-retardant polypropylene and spinning temperature;
抗滴落阻燃聚丙烯动态粘弹性能及其纺丝温度研究
2.
The scheme of process optimization of spinning temperature, quench air velocity, initial pressure of spin pack and spinning speed etc is put forward.
阐述了涤纶短纤维卷绕丝内在质量均匀性的重要性,分析了纺丝过程中影响原丝质量均匀性的主要因素,从纺丝温度、冷却风风速、组件初始压力、纺丝速度等方面提出了工艺优化的方案。
3.
The results showed that the 110 dtex/144 f fine denier PET FDY with splendid properties can be produced by decreasing impurity particle size,using nipple oiling method and selecting melt temperature 280 -282℃,spinning temperature 290 -292℃,cross air blow speed about 4.
结果表明:降低聚酯熔体中的杂质颗粒直径,选择熔体温度280-282℃,纺丝温度290-292℃,侧吹风速度约4。
3) laying temperature
吐丝温度
1.
Meanwhile,the effect of laying temperature and cooling speed on microstructure and peformance were studied.
介绍了唐山钢铁集团有限责任公司AWSER70S-6CO2气保焊丝用盘条的生产情况;分析了碳、锰、硅含量对该钢抗拉强度的影响和拉拔脆断产生的原因,以及吐丝温度和冷却速度对组织性能的影响。
2.
The effect of technological parameters of stelmor on the microstructure and properties of high carbon wire rolled at high speed has been studied The relationship between the microstructure and the properties of the wire rolled with different laying temperature and cooling rate has been analyzed Optimal technological parameters of stelmor have been obtaine
研究了 9mm高碳钢高速线材斯太尔摩工艺参数 ,分析了不同吐丝温度和模拟控制冷却速率对金相组织和力学性能的影响 ,确定了最佳的斯太尔摩工艺参数。
3.
The product quality is improved by optimizing chemical component, adjusting laying temperature and cooling speed to improve microstructure and property .
以牌号为GH60的钢种为例介绍高线生产含Ti焊丝的情况,通过优化化学成分、调节吐丝温度和冷却速度来改善组织性能,提高产品质量。
4) filament temperature
灯丝温度
1.
The relationship between filament resistivity and filament temperature for vacuum fluorescent display
真空荧光显示器灯丝电阻率与灯丝温度的关系
2.
The effects of decreasing filament temperature on growth of diamond films were reported.
研究了改变本底真空对薄膜质量的影响,给出了在该系统中得到质量较高金刚石薄膜的最小本底真空值;阐述了降低灯丝温度对薄膜质量的影响。
3.
In order to observe the phenomenon of the filament temperature drop caused by the board-current,the ideal diode filament temperature was detected precisely with an infrared thermometer.
为了观察由板流引起的灯丝温度下降现象,利用红外测温仪对理想二极管灯丝温度作了精密测量。
5) thread temperature
丝束温度
6) spinning temperature
抽丝温度
补充资料：铂电阻温度表(见电阻温度表)
铂电阻温度表(见电阻温度表)
表。bod旧nZu wendubiao铂电阻温度表见电阻温
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条