2) Design of Shot Blast Machine
抛丸室设计
3) flexible design
弹性设计
1.
In this article, by expatiating on the concept and importance of the flexible design, and analyzing example and summarize corresponding methods of design, explaining that the introducing of the flexible design indicates a kind of reformation of conception which means taking the time factor into account and considering a building as a whole life process.
通过对弹性设计概念和必要性的论述,分析实例,总结相应的设计方法,说明弹性设计思想与方法的引入标志着一种观念的革新,即在建筑设计中纳入时间的因素,将建筑作为全寿命过程加以考量。
4) elastic design
弹性设计
1.
The elastic design of box boom can be made through two-stage stress theory.
本文应用有限差分法,将起重机箱形伸缩臂挠曲微分方程变为代数方程求解,实现用二阶应力理论对吊臂进行弹性设计。
5) Trajectory design
弹道设计
1.
Because bending and being tracked of sound line make torpedo tailing after target to smaller depth,upper limit control trajectory is usually considered in torpedo trajectory design.
由于声线弯曲和鱼雷跟踪声线,使鱼雷跟踪目标到较浅深度,因此鱼雷弹道设计通常有上限控制弹道。
2.
A rapid iteration algorithm adapting to ballistic missile trajectory design is presented.
提供了弹道导弹弹道设计的一种快速迭代方法和模型。
3.
Moreover,the trajectory design based on some limiting factors during terminal phase guidance was theoretically discussed and some ad.
建立了比例导引法的修偏模型,对机动弹头末制导段弹道的弹道倾角和速度提出了要求,从而提出了末制导段弹道设计的基本思路,最后从工程的角度提出一些可供参考的设想和建议。
6) ballistic design
弹道设计
1.
With a combination of calculation and evaluation of charge ballistic schemes, a new charge ballistic design method based on multiple attributes is presented.
在传统火药装药弹道设计方法的基础上,将装药弹道模型的求解与评价相结合,给出一种基于多指标的弹道设计新方法。
2.
The dynamic model and kinematic model of ballistic design are set up by means of mechanics and modern mathematics for torpedo with side\|looking sonar, which are used to attack and defence against single targets.
为了实现具有旁侧视声纳鱼雷攻防对抗单一目标的模拟仿真,利用力学与现代数学的方法,建立了具有旁侧视声纳鱼雷攻防对抗单一目标的弹道设计动力学模型与运动学模型,并以此建立了鱼雷导引弹道段、平行航向弹道段和程序弹道段的数学模型,该模型的建立可以实现鱼雷攻击末弹道的仿真研究。
3.
This paper discusses the ballistic design which is the guide task and the keylink of the overall design of the weapon system.
论述了弹道设计是武器系统总体设计的先导任务和中心环节。
补充资料:1350mm双流板坯连铸机(重庆钢铁设计研究院设计)
1350mm双流板坯连铸机(重庆钢铁设计研究院设计)
叠 135Omm双流板坯连铸机(重庆钢铁设计研究院设计)
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条