1)  examination results
审核结果
2)  Auditing
审核
1.
Tentative Discussion Methods of Data Auditing in Environment Statistical;
浅论环境统计中数据的审核方法
2.
Cleaner production auditing in plating enterprise Part Ⅰ—summary of cleaner production auditing;
电镀企业清洁生产审核 第一部分 清洁生产审核概述
3.
Cleaner production auditing in plating enterprise PartⅡ-How to launch cleaner production auditing of plating industry;
电镀企业清洁生产审核 第二部分 电镀企业如何开展清洁生产审核
3)  verification
审核
1.
Discussion on working essentials of construction cost verification;
工程造价审核工作要点的探讨
2.
Discussion on the methods for project budget and settlement verification;
工程预结算审核方法探讨
3.
Combined with practical experiences of cleaner production verification over many years, the different roles of propaganda and education in the early stage, medium stage and later stage of cleaner production verification are elaborated.
本文根据多年来在清洁生产审核工作中的实际经验,论述了宣传教育在清洁生产审核工作前期、中期和后期的不同作用,并提出了不同时期应采用的具体形式,可为企业清洁生产审核提供一定的指导和借鉴作用。
4)  audit
审核
1.
Application of the process-method in innerquality management system audit;
过程方法在内部质量管理体系审核中的应用
2.
Engineering cost audit under engineering bill pricing mode;
论工程量清单计价模式下的工程造价审核
5)  examination
审核
1.
Consideration on engineering budget and final accounts examination;
关于工程预决算审核的思考
2.
Enhancing the accounts examination of engineering finished;
加强工程竣工结算的审核
3.
Points for ettention on API examination;
阀门企业在API审核中的注意事项
6)  check
审核
1.
Discussion on budget and settlement check of basic construction;
浅谈基本建设预结算审核
2.
Discussion on finishing settling check work of constructing projects by pricing list;
浅谈清单计价的建设工程竣工结算审核工作
3.
Discuss on problems in financial check of project cost;
关于工程造价预结算审核问题的探讨
参考词条
补充资料:测试结果可接受性的检查和最终测试结果的确定


测试结果可接受性的检查和最终测试结果的确定
check of the acceptability of test results and determination of the final test result

  C凡(3)二3.3d,时,取此3个结果的平均值作为最终侧试结果;否则取它们的中位数作为最终测试结果。。,为重复性标准差(即在重复性条件下所得侧试结果的标准差)。 在口田T 11792一1989中还对重复性和再现性条件下所得侧试结果可接受性的检查方法和最终测试结果的确定做了详细讨论和规定。(马毅林)ceshi 11叩uo kejieshCxjxing d6 iiancha he zuizhong ceshi】i闪旧de que心ing测试结果可接受性的检查和最终测试结果的确定(checkof山eac,ptability of test,ults助ddsterminationofthefi耐testresult)在商品检验中进行一次测试的情形不多见,当得到一个测试结果时,所得结果不可能直接与给定的重复性标准差作可接受性的检查。对测试结果的准确性有任何疑问时都应再进行一次测试。所以,对两个测试结果进行可接受性的检查是一般的情况。 可接受性的检查,实际上是一种统计检验。任何两个测试结果只要能通过可接受性的统计检验即可认为是一致的,均可接受。比如,在重复性条件下,所得结果之差的绝对值(下称绝对差)不超过相应的重复性限r(见重复性和再现性)的值,则认为两个结果是一致的,均可接受;如果两个侧试结果的绝对差超过r,则认为它们是不一致的,必须增加测试。 按国家标准《测试方法的精密度在重复性或再现性条件下所得测试结果可接受性的检查和最终测试结果的确定》(GBIT 1 1792一1989),在重复性条件下,如果两个测试结果的绝对差不超过r的值,可取两个侧试结果的平均值作为最终测试结果。如果两个结果的绝对差超过r的值,并且测试费用较低,须再做两次测试。当4个结果的极差(即其中的最大值与最小值之差)不超过相应的临界极差c,瓜(4)二3.6a,时,取4个结果的平均值作为最终测试结果。如果两个结果的绝对差超过r的值,并且测试费用较高时,只须再作一次测试。当3个结果的极差不超过相应的临界极差
  
说明:补充资料仅用于学习参考,请勿用于其它任何用途。