说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 点导引
1)  point guiding
点导引
2)  fad problem
热点引导
1.
Fad problems is news mediums lead the thought and public opinion of readers,audience,listeners to a right direction,so,when lead fad problems,should set up sense of general situation in ideology,have political sense,and hold the measurement of leading,at the same time,combine frontal reports and control publicopinons, to raise leading levels and results.
热点引导是新闻媒体把读者、听众、观众关于热点问题的思考、舆论引导到正确的方向上。
3)  node leading
节点引导
1.
This algorithm includes two parts,one is using node leading to ensure the dynamic connectivity of WMSN,and the other is combining average consensus filter with traditional distributed data fusion architecture to realize the optimizing distributed data fusion with low cost of communication.
为了满足无线移动传感器网络(WMSN)的目标跟踪应用要求,提出了一种分布式目标跟踪算法,可使用节点引导保证WMSN的网络动态连通性;在传统分布式数据融合体系结构的基础上,结合平均一致性滤波器实现了低通信开销的优化分布式数据融合。
4)  Three Point Trajectory Guidance Method
三点导引法
1.
Research on the Three Point Trajectory Guidance Method for Ship-to-Air Missile;
点导引法导引舰空导弹弹道研究
5)  four points and one leading
四点一引导
1.
according to the characters for technicality of the structural engineering construction and lessons of the architectural composition, the teaching methods and practice of " four points and one leading" are discussed.
根据土木工程施工专业的专业特色和房屋构造的课程特点,提出了“四点一引导”的开放式教学方法,同时介绍了其具体操作及实践效果。
6)  predicted point guidance
前置点导引
1.
Combining the advantages of azimuth guidance method and predicted point guidance method,an integrated guidance method for wire-guidance torpedo is presented.
在深入分析线导+尾流自导鱼雷方位导引和前置点导引方法的基础上,综合方位导引和前置点导引的优点,给出了一种线导鱼雷的组合导引方法。
补充资料:闭式单点、双点压力机
代码:00413
设备名称:闭式单点、双点压力机
型号规格:公称力≥800kN
计量单位:台
主要参数内容
国际先进国内先进国内一般国内落后评定方法及说明
(一)加工精度
    参照GB10924-89、GB10933-89、JB5200-91
1、滑块下平面对工作台上平面的平行度(mm)
30%精度储备20%精度储备达到规定值大于规定值 
0.02+0.10/100×滑块下平面的被测长度
     
2、滑块行程对工作台上平面的垂直度
30%精度储备20%精度储备达到规定值大于规定值 
0.05+0.02/100×滑块行程长度
     
(二)结构性能
     
1、离合器、制动器接通率,当滑块行程次数≤16次/分时为70%,≤25次/分时为60%,≤45次/分时为50%
大于规定值10%大于规定值达到规定值达不到规定值 
2、液压超负荷保险装置、微调装置、吨位指示器
全部具有全部具有部分具有没有 
(三)噪声dB(A)
     
1、公称力≤400kN
≤85≤87≤88>88 
2、公称力>400kN
≤87≤88≤90>90 
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条