1) rectangular section member
矩形截面杆
2) rectangular section
矩形截面
1.
Seven-freedom unit used for analysing the warping of rectangular section beam;
矩形截面直梁弯翘分析的七自由度单元法
2.
Calculation of bended structural member reinforcement of rectangular section of reinforced concrete;
简易法计算混凝土矩形截面受弯构件配筋量
3.
A spedal study is conducted of the effect of the rectangular section circulating bed edge angle on the gas-solid dual-phase flow and the radial porticle conecntration distribution.
特别是考察了矩形截面循环床边角对气固两相流动的影响。
3) rectangle section
矩形截面
1.
This essay offers the calculation of magnetic field along axis of finite long rectangle section spiral tube current,gives the resolution formula and illustration of the magnetic field, and draws some significant conclusions by discussing on the calculation.
计算了有限长矩形截面螺线管轴线上的磁场,给出了磁场的解析式和图示,并对计算结果作了讨论,得出了一些有意义的结论。
2.
The formula prescribed in Code for design of masonry structures, aimed to calculate influence coefficient (φ) for bearing capacity of biaxial eccentric rectangle section compression masonry members, is numerically analyzed, its bearing capacity would increase when its eccentricity of loading is added, a new substitutive .
为此,对《砌体结构设计规范》中关于无筋砌体矩形截面的双向偏心受压构件承载力影响系数φ值计算公式进行了分析,认为φ值在局部范围内存在着使承载力随偏心距增大而增大等缺陷,并给出了新的计算公式。
3.
This paper offers the formulas of calculating the ledger beam strength, compares the bearing capacity of the ledger beams with that of rectangle section beams.
提出了花兰梁截面强度计算公式,揭示了其较按矩形截面计算较大的承载能力和一定的经济效益。
4) rectangular cross-section
矩形截面
1.
After numerical simulation validity was confirmed by experimental results on cold model test,the erosion property in a circulating fluidized bed(CFB) with a rectangular cross-section was analyzed using numerical simulation under the condition of different primary/secondary air ratio,different up/down secondary air ratio and different front/back secondary air ratio.
在冷态试验对数值模型进行验证的基础上,通过模拟计算对不同一二次风配比、上下二次风配比以及前后二次风配比对矩形截面流化床锅炉内的磨损特性进行了分析。
2.
By analyzing all of the factors which will affect the eccentric distance limits of eccentric compression for rectangular cross-sections in this paper,it is believed that the eccentric distance can not be taken as the basis of eccentric compression,other.
文中通过分析影响矩形截面大小偏心受压偏心矩界限的所有因素,认为一般情况下把偏心矩的大小作为大小偏心受压的判别依据是不合适的,且还会因此在工程技术人员和初学者中形成对区别大小偏心受压的错误认识。
5) rectangular cross section
矩形截面
1.
A practical formula for calculating the conductance of the tube of rectangular cross section in the full pressure range has been obtained based on a viewpoint that was proposed by the author.
利用作者提出的分层流动模型流导计算理论 ,对矩形截面长管道的流导进行计算 ,得到了全压强范围内适用的流导计算公式 ,计算结果与经验公式结果相符 。
6) composite laminated bar
矩形厚截面层压杆
1.
In view of the effective elastic moduli theory , analyzing the thick composite laminated bars subjected to an externally applied torque are presented by three_dimensional finite element(3-D FEM) and global_local method in this paper.
本文根据有效弹性模量理论［１］，采用三维八节点等参数有限元和整体—局部方法，对复合材料大层数矩形厚截面层压杆的扭转问题及其自由边缘效应进行了分析研究，通过算例计算给出了剪切应力在横截面内的分布规律、杆的扭转变形及其在自由边缘区域层间应力的分布情况·由于本文的分析方法可根据需要仅在应力梯度较大的局部区域，按单层逐层划分单元或在单层内再细化单元，以求得单层内精确的应力场和位移场，因此能显著节约计算量与机时，为具有大层数层压杆的扭转强度计算提供了一种有效的方法
补充资料：R6m矩形坯连铸机在生产(邯钢)
R6m矩形坯连铸机在生产(邯钢)
R6m矩形坯连铸机在生产(邯钢)
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条