1) average uranium mass concentration
平均铀质量浓度
1.
The principle,method and case history how to predict the average uranium mass concentration in lixivium of in-situ leaching are introduced and the existing problems are discussed.
介绍了矿床采区浸出液中平均铀质量浓度的预测原理、方法和实例,并讨论了存在的问题。
2) average mass concentration
平均质量浓度
3) uranium concentration
铀质量浓度
1.
The modeling course on prediction of uranium concentration in pregnant solution from in-situ leaching of uranium is described, a mathematical model based on grey sysytem theory is put forward, and a set of computer application software is correspondingly developed.
详细介绍地浸采铀浸出液铀质量浓度预测模型的建立过程。
2.
In this paper briefly discusses the kinetic characteristics of in situ leaching and expounds the variation of uranium concentration in the leaching out liquor and rational wellfield layout.
阐述了地浸采铀的溶浸动力学特征 ,论述了浸出液铀质量浓度变化及井场的合理布
4) mean mass molarity
平均质量摩尔浓度
5) average concentration
平均浓度
1.
Basing on Chebyshev inequality and on the computation of average concentration of all related subsets, the authors put forward and proved the following lemma, theorem, and the four corollaries: [Lemma 1] There exists at least one of the sets of generalized prime-twins (namely one subset of the set of 2-primes group), which is an infinite set.
基于Chebyshev不等式以及对所有相关子集平均浓度的计算,提出并证明了下列引理、定理,以及4条推论:[引理1]至少有1个广义孪生素数集合(或称2素数组子集)是无限集合;[定理1]全部的或无限多的广义孪生素数集合是无限集合;[推论1]至少有1个3生素数集合(或称3素数组子集)是无限集合;[推论2]全部的或无限多的3生素数集合是无限集合;[推论3]普遍地说,至少有1个h生素数集合(或称h素数组子集)是无限集合(h是≥2的整数);[推论4]普遍地说,全部的或无限多的h生素数集合是无限集合(h是≥2的整数)。
6) equilibrium mass concentration
平衡质量浓度
1.
Phosphate adsorption characteristics onto surface sediments from aquaculture area in Sungo bay were studied in laboratory simulating condition,and phosphate adsorption-desorption equilibrium mass concentration was also analyzed.
在室内模拟扰动条件下,研究了桑沟湾养殖水域表层沉积物对磷酸盐的吸附动力学及其吸附等温线,探讨了磷酸盐的吸附-解吸平衡质量浓度以及沉积物的源汇角色。
补充资料：对数平均浓度差
分子式：
CAS号：
性质：指传质过程中两端点(传质设备前后)浓度差ΔCa、ΔCb的对数平均值ΔClm=。当平衡线及操作线均可视为直线、总传质系数可取为常数时，△Clm即为传质过程的平均推动力。
CAS号：
性质：指传质过程中两端点(传质设备前后)浓度差ΔCa、ΔCb的对数平均值ΔClm=。当平衡线及操作线均可视为直线、总传质系数可取为常数时，△Clm即为传质过程的平均推动力。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条