1)  cross-section mass
面质量
1.
A specific WHA(tungsten heavy alloy) component is embedded in the WHA-ballast EP case as a ballast to increase the cross-section mass(penetrator weight to cross section area ratio) which plays a dominant role in EPW(earth penetrator weapon) penetration capability.
将特殊设计的钨合金结构作为镇重体填加至钻地弹的壳体内部,以提高钻地弹的整体密度,增大面质量,从而提高了钻地弹的侵彻能力。
2)  overlay quality
贴面质量
3)  surface quality
表面质量
1.
Effect of rolling oil on the surface quality of annealed aluminum foils;
轧制油对铝箔退火表面质量的影响
2.
Experimental research on surface quality in two-dimensional ultrasonic grinding of nano-complex ceramics;
二维超声磨削复相陶瓷加工表面质量的试验研究
3.
Effects of additives on the surface quality of cathode zinc;
添加剂对电锌表面质量的影响
4)  surface finish
表面质量
1.
Bye the instance of the U-bending,this paper analyses how the construction of the bending die will impact the surface finish of the bending part,proposes some construction of the U-bending die for improving the surface finish of the bending part.
以U形弯曲为例,分析了弯曲模结构对弯曲件表面质量的影响,提出了提高工件表面质量的几种弯曲模结构方案,并着重介绍了其设计要点。
2.
The effects of α-starch on properties of moulding sand and surface finish of steel casting are studied.
研究了α淀粉对型砂性能和铸钢件表面质量的影响。
5)  mass of mat surface
毡面质量
6)  cross section quality
断面质量
1.
The experimental results indicate that the minimum discharge voltage of piercing ascents with the increasing of blank thickness and cross section quality is better when the discharge voltage is higher than the minimum discharge voltage under the same blank thickness.
研究结果表明:冲孔所需最小成形电压随着板料厚度的增加而增加;对于同一厚度的铝板,当电压大于最小冲孔电压时,电压越大,断面质量越好;在3种成形方式中,板坯上下放置弹性传压介质的成形方式毛刺区域最小,断面质量最佳,但所需能量最大。
2.
An analysis was made on the influences of big-clearance blanking to the cross section quality of the parts and to the wear of the dies.
对大间隙冲裁与冲件断面质量、模具磨损的影响进行了分析 ,并提出了提高模具寿命的具体方
参考词条
补充资料:蚕茧质量监督检查和国家生丝质量检验


蚕茧质量监督检查和国家生丝质量检验
cocoon quality supervision inspection and national silk quality inspection

  检验局承担并组织有关检验机构对全国已核发生产准产证的缘丝、绢纺企业的生丝、绢丝质量进行抽查检验(两年共四期),以考核生产企业生丝质量水平。中国桑蚕鲜茧评茧计价方法主要有3种:①鲜上光茧干壳量仪器评定(简称仪评)计价;②“组合售茧、嫌丝计价,’(简称“组、缎”)评茧方法;③茧层率评茧计价。国家质量技术监督局于19望)年6月7日下发了《关于加强茧丝质t监督工作的通知》,要求加强桑蚕鲜茧收购期间的质量监督执法检查;重点做好鲜茧收购过程中“四率”(仪器配备率、仪器完好率、仪评率和仪评相符率)的检查工作。各级专业纤维检验机构应充分发挥职能作用,加强蚕茧质量监督管理;加强对茧站仪评计价工作指导;加强对蚕茧收购计t器具的检定工作;充分运用法律手段,在蚕茧收购期间开展执法检查活动,对违法行为坚决予以查处。 在国家生丝质t检验方面,1998年国家经贸委等4部门联合发布了(缀丝绢纺准产证制度实施办法》,规定缎丝、绢纺企业准产的基本条件。经国家茧丝绸协调小组审议,并报国务院领导批准,“国家生丝质量检验”项目列人(国家茧丝绷发展风险基金》第二批发展项目。该项目由中国纤维检验局承担并组织依法设t或依法授权的具有生丝、绢丝检验能力的纤检局(所)、生丝质检站对全国已核发生产准产证的缀丝、绢丝企业的生丝、绢丝质量进行检验。(吕善模),ngconjian zhilia叩Jiondu iianCha he gUOJia she叩51 zh1旧nyan蚕茧质一监督检查和国家生丝质t检验coon甲ality su伴币sion inspection and natsilk卿ality ins衅tion)专业纤维检验机构蚕鲜茧收购期间,对茧站收购鲜茧进行质量监督和检验的全过程。国家生丝质量检验是指由中国CO-nal桑查维
  
说明:补充资料仅用于学习参考,请勿用于其它任何用途。