1) impulse control force
脉冲控制力
1.
Based on a ballistic model, the relationship between corrected distance and the magnitude of impulse control force is studied, and relationship between the miss distance and the class number of impulse control force analyzed.
从弹道的角度建立弹道模型,分析了修正距离与脉冲控制力大小的关系以及脉冲发动机级数与脱靶量之间的关系。
3) impulse force control
脉冲推力控制
1.
In order to research motion laws of mortar projectiles under impulse force control at terminal trajectory,impulse force and moment were analyzed,and the mathematical model for the trajectory under control was established.
为研究迫弹在弹道末段受脉冲推力控制时的运动规律,分析了迫弹受到的脉冲发动机的控制力和控制力矩,建立了有控弹道模型。
4) pulse pressure control
脉冲压力控制
5) pulse control
脉冲控制
1.
The compositions of gas heating roller-type mesh belt furnace production line,gas pulse control and air/gas ratio continuously adjusting technologies,and multi-media distributed computer control system were introduced.
介绍了燃气加热托辊型网带炉生产线的组成、燃气脉冲控制和空气/燃气比例连续调节技术和计算机多媒体集散控制系统。
2.
The global asymptotical synchronization of two chaotic systems is realized simply by using the linear error feedback from the state variables of drive and response systems as pulse control signal.
基于脉冲微分方程的稳定理论,针对一类混沌系统,提出了一种脉冲控制同步的方法·该方法仅采用驱动系统与响应系统状态变量的线性误差反馈作为脉冲控制信号,实现了两个混沌系统的全局渐近同步·给出了两个混沌系统实现全局渐近同步的判据·当采用相同的脉冲控制矩阵和相等的脉冲间隔时,两个混沌系统实现全局渐近同步的判据可以被简化·该方法适用于一大类混沌系统的同步控制·以Lorenz混沌系统为例,进行了控制器的设计·所设计的控制器结构简单,易于实现,收敛速度快·理论分析和数值仿真结果证明了该方法的有效性
3.
Seismic responses of a typical arch dam are studied by use of the principle of pulse control for the first time.
首次运用脉冲控制原理对一混凝土典型拱坝的地震响应进行了分析。
6) impulse control
脉冲控制
1.
The minimum cost problem on a class of impulse control model;
一类脉冲控制模型的最小费用问题
2.
An impulse control of stochastic Navier-Stokes equation
随机Navier-Stokes方程的脉冲控制
3.
In view of the problem of correction of the end of ballistic trajectory of mortar,this paper builds a dynamics model based on impulse control and analyzes the effect of impulse and trajectory parameters on terminal correction ability and trajectory characteristic.
针对迫弹的末段弹道修正问题,建立了基于脉冲控制的飞行动力学模型。
补充资料：控制离心力
用常规切削速度和转数使用可转位刀片是60年代之后铣削技术的新台阶。当前在高速切削领域除了整体硬质合金刀具外还有可转位刀具。优先使用的领域是铝合金加工和刀具、模具制造。
 |  |
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条